To Next PageTo Next PageWhat to do if Jacobsen Eclipse 122F Lawn Mower engine will not start?
If your Jacobsen Lawn Mower engine won't start, it could be due to several reasons: * The fuel tank might be empty or contain dirty fuel. Drain the tank and refill it with fresh, clean fuel. * The fuel shut-off valve might be closed. Open the fuel shut-off valve. * The engine switch might be off. Turn the engine switch to the On position.
Why Jacobsen Lawn Mower engine hard to start or runs poorly, looses power or stalls?
If your Jacobsen Lawn Mower engine is hard to start, runs poorly, loses power, or stalls, consider these potential causes: * Use the proper grade of clean fuel. * Check the spark plug wire for loose connections. * Clean the air intake and air cleaner. * Clean the fuel cap to ensure the vent isn't plugged.
What to do if Jacobsen Eclipse 122F reel does not cut, or cuts unevenly?
If the reel on your Jacobsen Lawn Mower isn't cutting or is cutting unevenly, here's what you can do: * Adjust the reel to the bedknife. * Ensure the reel switch is turned on. * Check the LCD display for reel motor faults and service the reel motor if necessary. * Fully charge the battery pack. * Adjust the generator output if there's an over-voltage condition.
Why is my Jacobsen Lawn Mower engine hard to start and stalls?
If your Jacobsen Lawn Mower engine is hard to start, runs poorly, loses power, or stalls, consider these potential causes: The choke might be in the wrong position (refer to the Engine Manual), the fuel could be dirty or incorrect (refill with the proper grade of clean fuel), there might be loose wiring (check the spark plug wire), the air intake could be plugged (clean the air intake and air cleaner), or the vent in the fuel cap might be plugged (clean the fuel cap).
Why Jacobsen Eclipse 122F Lawn Mower unit does not have power?
If your Jacobsen Lawn Mower unit isn't getting power, there are several potential causes: * The power connector might be disconnected, so ensure it is properly connected. * The batteries could be discharged; in this case, fully charge the battery pack. * The engine might not be running; start the engine before trying to energize the unit. * A 50 Amp fuse might be blown; open the battery tray to check and replace the fuse if needed. * The 20 Amp circuit breaker could be tripped; try resetting it. * The battery might be defective; perform a load test and replace the batteries if necessary. * The O.P.C. bail might be engaged; disengage the bail and restart.
What to do if Jacobsen Lawn Mower does not react properly to O.P.C. Lever?
If your Jacobsen Lawn Mower isn't reacting properly to the O.P.C. Lever, here are a few things you can check: * Ensure the power switch is on by following the proper start-up procedure. * Make sure the parking brake is disengaged. * Verify the reel switch is in the on position. * Inspect the belts for any damage and replace them if needed. * Calibrate the bail lever. * Check the LCD display for traction motor faults and service the traction motor if necessary.
What to do if Jacobsen Lawn Mower reel does not cut?
If the reel on your Jacobsen Lawn Mower doesn't cut or cuts unevenly, it could be due to several reasons: The reel to bedknife might not be adjusted properly (adjust it), the reel switch might be in the off position (turn it on), there could be a reel motor fault (check the LCD display and service the reel motor), the battery charge might be low (fully charge the battery pack), or there could be an over voltage condition (adjust the generator output).
How to fix Jacobsen Lawn Mower that does not react properly to O.P.C. Lever?
If your Jacobsen Lawn Mower isn't reacting properly to the O.P.C. Lever, check the following: Ensure the power switch is on by following the proper start-up procedure. Make sure the parking brake is disengaged. Verify the reel switch is in the on position. Inspect the belts for breakage and replace them if needed. Calibrate the bail lever. If there's a traction motor fault, check the LCD display and service the traction motor.
General| Brand | Jacobsen |
|---|---|
| Model | Eclipse 122F |
| Category | Lawn Mower |
| Language | English |
Instructions for safe operation of the mower, emphasizing operator awareness and proper use.
Details safety alert symbols (Danger, Warning, Caution, Notice) and general safety precautions.
Displays important safety decals, including DANGER and WARNING messages for safe operation.
Describes the function of handle controls: Parking Brake, Speed Paddle, O.P.C. Bail, Key Switch, Reel Switch, Circuit Breaker, LCD Display.
Details the LCD display functions, audible alerts, and alert displays for system voltage and motor faults.
Explains the purpose of the Interlock System and how to test its functionality.
Provides essential operating procedures, safety precautions, and guidelines for mowing.
Step-by-step instructions for starting and stopping both Battery Power and Gen-Set Power modules.
Details mowing techniques, pattern suggestions, and safety during operation.
Covers daily maintenance tasks like greasing, cleaning, and checking oil and fuel.
Checks reel bearings, blades, and bedknife condition prior to adjustment.
Detailed steps for adjusting the bedknife to the reel for optimal cutting.
Instructions for setting the cutting height of the mower.
Checks reel bearings, blades, and bedknife condition prior to adjustment for floating heads.
Detailed steps for adjusting the bedknife to the reel for optimal cutting with floating heads.
Instructions for setting the cutting height of the mower with floating heads.
Critical safety warnings regarding battery handling, charging, and potential hazards.
Instructions for operating the battery charger, including AC voltage selection and safety.
Detailed instructions for installing batteries into the battery pack assembly.
Procedures for removing and installing the battery pack, including safety precautions.
Information about the engine manual, break-in procedures, and oil change recommendations.
Instructions for checking and changing the engine oil, including oil type and intervals.
Safety precautions for handling, storing, and using fuel for the generator.
Procedures for backlapping and grinding reel blades for optimal cutting edge.
A chart listing common problems, possible causes, and recommended actions for troubleshooting.
