65
I Cleaup Cycle
The cleanup cycle occurs once per day at 12:00 pm (noon) for
two minutes. This is not user programmable. The Jets Pump 1
and the Circulation Pump will turn on for one minute and then
shut off. Then Jets Pump 2 will turn on and run for 1 minute
then shut off. Be aware, the factory programmed cleanup cycle
cannot be canceled or altered!
I Blow-Out Cycle
This cycle will purge the air from the plumbing lines normally
caused by draining and filling the spa. The Jets Pump 1 and the
Circulation Pump will turn on for 1 minute and then shut off.
Then Jets Pump 2 will turn on and run for 1 minute then shut
off. This cycle will only occur:
- At start up.
- After exiting a service lock.
I Water Care Programming
Water care is crucial to maintaining a healthy and clean spa.
The CLEARRAY water purification system leads the way by sani-
tizing the water using a UV light bulb. Your spa can be pro-
grammed to remind you when to check and replace certain
components.
From the “Settings” menu, tap or to highlight the “Wa-
ter Care”menu tab in Orange.
Tap to the enter the menu. Then select one of the
features.
Programming the CLEARRAY UV Bulb Timer
The CLEARRAY UV bulb has a life expectancy of 1-year. A timer
activates when power is applied and begins a countdown star-
ting at 365 days. Once the timer expires, an error message will
appear of the display, the UV bulb must be replaced and the ti-
mer needs to be reset.
Tap to enter the Programming Menu.
Note: The days are stored in memory if the power is interrupted.
From the “Water Care” Menu you can to set the CLEARRAY UV
bulb timer.
Tap or to change the days in 10-day increments. The
range is from 0 to 365 days.
Note: The CLEARRAY UV timer counts down by days not usage.
Note: to ensure the appliance works correctly, do not deacti-
vate this function; program it as specied.
Tap to confirm and save your changes.
When the timer expires, a message will appear on the control
panel display. The CLEARRAY UV bulb must be replaced and
the timer must be reset. Tap “reset” and follow the instructions
above to reset the timer. If you tap “snooze” the message will
clear but the error icon (
) will display and the reminder
screen will reappear in 10 days.
Tap to return to the “Water Care” Menu. Tap again to re-
turn to the Settings Menu.
Programming the Water Change Timer
A programmable “Water Refresh” reminder can be set to re-
mind you when to drain and refill the spa. Tap
to enter the Programming Menu.
From the “Water Care” Menu you can to set the “Water Refresh”
timer.
Tap or to change the days in 30-day increments. The
range is from 0 to 180 days.
If the electrical power supply is disconnected,the countdown is saved
in the memory.
Note: to ensure the appliance works correctly, do not
deactivate this function; program it as specified.
Tap to confirm and save your changes.
When the timer expires, a message will appear on the control
panel display. The water must be drained and replaced with
fresh water. Follow the instructions above to reset the timer. If
you tap “snooze”the message will clear but the error icon (
)
will display and the reminder screen will reappear in 10 days.
Refer to Section“Cleaning the Filter Cartridges”for filter location.
Tap to return to the “Water Care” Menu. Tap again to re-
turn to the Settings Menu.
Programming the ProClarity/ProClear Filter Timer
A programmable filter timer can be set to remind you when to
clean or replace the filters and skimmer bag. Tap
to enter the Programming Menu.
ProClarity 60
Reminder
This is a general
reminder. Please change
your water soon.
snoozereset
60
60 days left
add
days
Water Refresh
Water Refresh
60
65
65 days left
add
days
CLEARRAY
Reminder
It’s time to replace your
CLEARRAY bulb. Contact
your authorized dealer for
replacement parts.
snoozereset
CLEARRAY 65
ProClarity 60
Water Refresh
60
ProClarity Depth
50
CLEARRAY 65
Water Care
Heat & Filter
Water Care
Wi-Fi
SETTINGS
Water Care
To Next Page
Loading...
Need help?
General
