HELLO? SPEAKERPHONE? YES!
BLUETOOTH
®
CONNECTION, CONTINUED
Like any amazing couple, this one starts with a connection — one between
your device and the speaker’s Bluetooth. Here’s how it works:
1. Make sure the smartphone, tablet, or computer you’re using with the
speaker has Bluetooth.
2. Turn on the speaker (press and hold the power button for 5 seconds) and
look for the little blinking light.
3. Do whatever your device needs you to do on its end.
4. Look for JAM Double Down in your device’s Bluetooth list or click YES.
5. Now hit PLAY on your speaker and crank it up — or down if you’re lame.
The device and Bluetooth will find each other every time, as long as the speaker is set
to Bluetooth and your device’s Bluetooth is, you know, on.
If you’re connecting to a computer, you may have some extra steps on that end. You’ll
have to get that information from the computer company.
Depending on your device, you may be prompted to enter a pairing code. If prompted,
enter “0000” as the code.
To disable pairing of an existing device and pair a new device, press and hold the
play/pause button for 3 seconds to activate pairing mode.
Note: If you turn on your JAM Double Down but haven’t started the party yet, it will
automatically power off after 2 minutes of unpaired inactivity.
Note: Once you've paired, if you pause the party for 15 minutes or more, the Double
Down will automatically shut off to preserve battery power.
Note: You should never have to do this, but in the event the speaker controls are not
operable, press and hold the play/pause button for 3 seconds to reset the speaker.
When friends call asking to join the party — and you know they will — answer the phone without disconnecting from your Double
Down. Yes, that’s right. Your speaker is a speakerphone, too. How amazing is that? Here’s how it works:
1. Make sure your phone and speaker are connected through Bluetooth.
2. Answering and ending a call works the same way: simply click the PLAY/PAUSE button on your Double Down.
3. If you’d rather not talk, hold down the PLAY/PAUSE button on your Double Down for 3 seconds to ignore the call.
THE COOLEST PART: The Double Down knows when a call is coming in and pauses the music before ringing. When you hang up, the
music starts where it left off — and so does the party. If it’s you making the call, just start dialing from your phone, and the Double
Down automatically does its hands-free thing. Isn’t it refreshing to know your speaker totally gets you?
Check out the chart below for a complete guide on handling calls with your Double Down.
Note: When handling calls in Jam2 mode, only the master speaker (that’s the left one) can control the call.
COMING CLEAN
A soft, dry towel is all you need to
clean off your speaker. Using water,
harsh cleaners, or anything else only
starts messing with the mechanics
inside. So, yeah, don’t do it.
HOOKING UP OLD-SCHOOL AUDIO, JACK
1. Plug one end of the cord into the speaker and the
other into the headphone jack on your device.
2. Turn on the speaker.
3. Hit PLAY on your device and crank it up — or down if
you’re lame.
You’ll have to play and pause the music from your device,
not your speaker. No problem. You’re there anyway, right?
Note: In Jam2 mode, only the speaker with the auxiliary
connection will play.
1. Press and hold the
power button for 5
seconds to turn on.
2. Follow the
instructions above to
pair your speaker.
3. Press play on your
device and crank it
up — or down if
you’re lame.
1. Turn on speaker 1 (press and hold the power button for 5 seconds).
2. Turn on speaker 2 (press and hold the power button for 5 seconds).
3. The speakers will begin to pair together automatically. This will take
a few seconds.
4. Voice prompts will indicate when speakers are paired together.
5. Follow the instructions above to pair your speakers to your device.
Choose Jam2 from your device’s Bluetooth list.
6. Press + and – together to toggle between stereo and mono modes.
Note: If either of your speakers have been previously paired to a
device, or will not pair automatically, press and hold the play/pause
buttons on both speakers for 5 seconds to activate pairing mode.
You will know they have reached pairing mode by the red and blue
blinking light.
2m
15m
PAIRING ONE SPEAKER PAIRING TWO JAM DOUBLE DOWN SPEAKERS TOGETHER
Bluetooth
Devices
JAM Double Down
on
>
Bluetooth
Devices
Jam2
on
>
Track 1
Auxiliary cable not included.
Situation
Short Press Play/Pause Button Long Press Play/Pause Button
1
st
Incoming call
2
nd
Incoming call
On call
Both calls active
Pick up call
End call
Call 1 on hold, pick up call 2
Hang up call 1, switch to call 2
Reject call
Move call from speaker to device
Reject call 2
Switch between 1
st
call and 2
nd
call
To Next Page
Loading...
Need help?
General
