Jandy Infinite WaterColors IWCP50W100

Other manuals for Jandy Infinite WaterColors IWCP50W100

Manual2 pages

Questions and Answers

C
collinserikaAug 14, 2025
How to fix Jandy Controller when lights don't turn on?
- K
  kblackwellAug 14, 2025
  If the lights don't turn on, here's what to check: * **Power:** Make sure the Light Controller is getting power. LED2 should be lit. * **Communication:** Verify the RS4-85 connection. LED1 should be blinking, indicating communication with automation. * **Wiring:** Ensure the lights are correctly wired to the Light Controller output. * **Light Failure:** It's possible the lights themselves have failed. If using niched pool and spa LED lights, try swapping the PCBA or replacing the light.
B
barbermarkAug 17, 2025
What to do if Jandy Controller lights are on but not switching colors?
- M
  Maria KellyAug 17, 2025
  If your lights are on but not changing to the color you've selected, there are a couple of things to investigate: * **Compatibility:** Confirm that you're using Infinite WaterColors Lights. Other types of lights aren't compatible. * **Zoning:** Make sure the lights are in the same zone that you are trying to control.
J
john67Aug 20, 2025
Why are my Jandy Underwater lighting lights flashing yellow?
- B
  Bobby MillsAug 20, 2025
  If your Jandy Underwater lighting is flashing yellow, it might not be communicating with the Infinite WaterColors LED Light Controller, or it could be connected to a non-compatible controller or transformer. First, ensure the lights are powered by the Infinite WaterColors LED Light Controller. If they are not, connect them and try again. If the lights are powered by the correct controller, check the RS-485 connection.
K
Karen HerreraAug 25, 2025
How to fix Jandy Underwater lighting that doesn't turn on?
- A
  Ashley RogersAug 25, 2025
  If your Jandy Underwater lighting doesn't turn on, the lights might not be powered, or they may have failed. Check the 120VAC power supply into the transformer and the 14VAC output at the transformer. Also, ensure the lights are enabled via the iAquaLink app. Check or reset the GFCI. Ensure that 120 volts has not been used in the installation, as this will cause damage that is not covered under warranty. If the lights have failed, consider replacing the light or swapping the PCBA.
D
dcruzAug 27, 2025
Why do I see different colors from different Jandy Infinite WaterColors IWCP50W100 Underwater lighting?
- V
  Veronica CummingsAug 27, 2025
  If you notice different colors from different Jandy Underwater lighting, it's possible that the zones are set differently. Ensure that all lights are in the same zone or that all zones are set to the same color.
J
John SmithAug 30, 2025
What to do if Jandy Infinite WaterColors IWCP50W100 Underwater lighting is out of sync?
- E
  edward83Aug 30, 2025
  If your Jandy Underwater lighting is out of sync, the zones might be set differently. Verify that the lights are in the same zone or that the same light show is applied to all zones.
S
Sarah SullivanSep 2, 2025
Why is my Jandy Infinite WaterColors IWCP50W100 dim, blinking, or not working?
- B
  Barbara HoffmanSep 3, 2025
  If one or more Jandy Underwater lighting lights are dim, blinking, or not working, it could be due to a poor connection or improper wire gauge. To troubleshoot, separate each light and independently wire 14VAC to a single light only, repeating this process for each light. If a junction box is being used, check for proper connection of the light cord. Also, verify that the correct wire gauge is being used between the transformer and the junction box.
D
Daniel Johnston MDSep 6, 2025
Why are my Jandy Controller lights flashing yellow?
- S
  Samantha SchmidtSep 6, 2025
  If your lights are flashing yellow, it likely means they're receiving power but aren't communicating correctly with the Light Controller. Double-check that the lights are wired directly to the Light Controller. Other transformers are not compatible and can cause this issue.
G
gregory50Sep 9, 2025
Why some of my Jandy Controller lights come on, but not others?
- N
  Neil SanchezSep 10, 2025
  If some, but not all, of your lights are turning on, it might be because the lights are assigned to separate zones. Check and ensure all the lights are in the zone you've selected.

Summary

Product Introduction and Safety

Jandy Infinite WaterColors LED Lights Overview

Introduction to Jandy Infinite WaterColors Pool & Spa LED Lights.

Critical Safety Warnings

Highlights essential safety warnings for installation and operation.

Regulatory Compliance

FCC Regulatory Compliance Statement

Details compliance with Part 15 of the FCC Rules for the device.

Safety Information and Precautions

General Safety Instructions and Warnings

Mandatory instructions for safe installation and operation of LED lights.

Installation Location and Installer Notes

Guidelines on pool installation placement and information for installers.

Product Application Notice

Specifies intended use for fresh and salt water swimming pools.

Product Overview and New Construction Installation

Product Model Specifications

Table detailing model numbers, light size, voltage, watts, and cord length.

New Construction Installation Requirements

Steps and requirements for installing lights in new pools or spas.

Preparing Fixture for New Installation

Pre-installation steps for the light fixture in new construction.

New Construction Installation Details

Junction Box and Bonding Requirements

Details on junction box placement, bonding, and wet niche installation.

Installing the Light Fixture

Procedure for physically installing the light fixture into the niche.

Existing Pool or Spa Installation

Electrical Safety for Existing Installations

Safety warnings and code requirements for existing pool installations.

Preparing Fixture for Replacement

Steps to prepare the light fixture for replacement.

Replacing the Light Fixture

Procedure for removing and installing a replacement light fixture.

Controller Wiring Options

General Wiring Notes and Precautions

Important notes on wiring, dimming, and power supply connections.

Wiring to AquaLink RS Control System

Instructions for connecting lights to the AquaLink RS control system.

Wiring to the Light Controller

Steps for connecting wires to the specific light controller.

iAquaLink App Features

Light Setup and Assignment

Guide to setting up and assigning lights within the iAquaLink app.

Naming Light Zones

Procedure for naming custom light zones in the app.

Selecting and Adjusting Colors;Brightness

Controlling light colors and brightness via the iAquaLink app.

OneTouch Setup Guide

Assigning Lights in OneTouch

Steps to assign lights to zones using the OneTouch controller.

Naming Light Zones in OneTouch

Procedure for naming light zones via the OneTouch controller.

Selecting Colors in OneTouch

How to select light colors using the OneTouch controller.

Amazon Alexa Light Control

Integration Information

Details on controlling lights via Amazon Alexa.

Troubleshooting Common Issues

Lights Not Powered or Out of Sync

Resolving issues with lights not turning on or synchronization problems.

Dim, Blinking, or Non-Working Lights

Troubleshooting for lights that are dim, blinking, or not functioning.

Lights Flashing Yellow or Color Mismatches

Diagnosing and fixing yellow flashing lights or incorrect colors.

Pool Light Replacement Parts

Pool Light Exploded View and Part Numbers

Diagram and list of parts for pool light replacement.

Field Replaceable Pool Light Components

Identifying components that can be replaced in the field.

Spa Light Replacement Parts

Spa Light Exploded View and Part Numbers

Diagram and list of parts for spa light replacement.

Field Replaceable Spa Light Components

Identifying components that can be replaced in the field.