Jasco PU-1580 User Manual (English)

Other manuals for Jasco PU-1580

Questions and Answers:

M
Megan LopezAug 21, 2025
What to do if Jasco PU-1580 Water Pump shows TROUBLE UNDER PRESS errors?
- A
  Aaron VasquezAug 21, 2025
  If the Jasco Water Pump experiences 'TROUBLE UNDER PRESS' errors, it might be due to air bubbles in the pump head. To resolve this, open the purge valve to remove the air bubbles. Another cause could be a clogged inlet filter, especially if using buffer solutions; in this case, replace the inlet filter. Also, check for a leaking plunger seal and tighten the pump head securing screws. If leaking continues, replace the plunger seal. A leaking inlet tube fitting can also cause this issue; tighten the fitting. In some cases, the pump head might be deteriorating, requiring thorough cleaning with an acid or alkaline solution. If the leak occurs at the downstream side of the pump, refer to the appropriate manual.
O
Olivia CarterAug 25, 2025
What to do if Jasco Water Pump displays TROUBLE OVER PRESS errors?
- M
  Michele WalterAug 25, 2025
  If your Jasco Water Pump displays 'TROUBLE OVER PRESS' errors, it may be due to a clog on the downstream side of the pump, such as in the manual injector, autosampler, column filter, tubing, or fittings. Refer to the appropriate manual for troubleshooting these components. Another cause could be a clogged line filter; replace it. If the internal damper or internal tubing is clogged, this requires service by trained JASCO service personnel. Contact your local JASCO distributor.
C
Christopher ZamoraAug 26, 2025
Why does my Jasco PU-1580 Water Pump have high baseline noise?
- Y
  ykimAug 27, 2025
  High baseline noise in your Jasco Water Pump can stem from several causes. Variations in pump pressure can contribute to baseline noise; see Section 2.1.3 for related information. Mixing noise, especially when running a gradient program or using a post-column derivatization system, can also cause this issue; consider adding an extra mixer or damper to the pump. Detector cell problems like bubbles, contamination, or leakage can also lead to high baseline noise; refer to the maintenance manual of the UV detector. A decrease in the light intensity of the detector, due to light source or mirror deterioration, can also cause this issue; refer to the maintenance manual of the UV detector.
S
Sara LiAug 28, 2025
Why is the bottom panel drain port of my Jasco PU-1580 leaking?
- B
  brandoncrawfordAug 28, 2025
  If the bottom panel drain port of your Jasco Water Pump is leaking, it could be due to deterioration of the diaphragm on the plunger washing mechanism; in this case, replace the diaphragm. Alternatively, it may be due to leakage from the plunger seal. If the head mount flange hole is clogged, solvent will leak from the drain hole.
S
Stefanie DennisAug 30, 2025
Why does Jasco Water Pump have spike-shaped baseline noise?
- L
  Larry DawsonAug 30, 2025
  If you observe spike-shaped baseline noise in your Jasco Water Pump, it could be due to bubbles in the cell, which causes noise toward increasing absorption; refer to the maintenance manual for the UV detector. Another cause could be electrical noise; in this case, ground the instrument.
K
Kimberly RothAug 31, 2025
Why is the retention time lengthening in my Jasco Water Pump?
- D
  davisjerryAug 31, 2025
  Lengthening retention time in your Jasco Water Pump can occur due to a decrease in the actual flow rate; see Section 2.1.2 for details. Insufficient column re-equilibration can also cause this; increase the column re-equilibration time. Variations in ambient temperature can affect retention time; protect the column using thermal insulation. Changes in eluent composition can also contribute; prepare the eluent again.
H
Heather FowlerSep 4, 2025
Why is the retention time shortening in my Jasco Water Pump?
- C
  clarkmelodySep 4, 2025
  Shortening retention time in your Jasco Water Pump can be attributed to column deterioration; consider replacing the column. Variation in ambient temperature can also affect retention time; protect the column using thermal insulation. Another cause can be variation in eluent composition; prepare the eluent again.
V
vbrooksSep 5, 2025
Why are ghost peaks appearing in my Jasco Water Pump?
- K
  katrina06Sep 6, 2025
  Appearance of ghost peaks in your Jasco Water Pump can be due to contamination of the pump or equipment upstream from the pump; clean using an acid or an alkaline solution. Eluent contamination can also cause ghost peaks; use a higher grade eluent. Another cause is contamination in the sample injection section, such as the manual injector or autosampler; clean any equipment that has been determined to be contaminated.
V
vbeardSep 7, 2025
Why is there poor reproducibility for retention time in my Jasco Water Pump?
- A
  Alejandro PerkinsSep 7, 2025
  Poor reproducibility for retention time in your Jasco Water Pump can be caused by variations in pump flow rate. Also, using an improper eluent can affect retention time; examine the eluent conditions. Variations in ambient temperature can contribute to poor reproducibility; protect the column using thermal insulation.
M
Mason GilesSep 9, 2025
What to do if the inlet tube fitting leaks on Jasco Water Pump?
- D
  Debra HollowaySep 9, 2025
  If the inlet tube fitting on your Jasco Water Pump is leaking, replace the Teflon packing on the front side of the fitting.

Jasco PU-1580 Specifications

General

Brand	Jasco
Model	PU-1580
Category	Water Pump
Language	English

Jasco PU-1580 Maintenance Manual

Table of Contents

Other manuals for Jasco PU-1580

Questions and Answers:

Jasco PU-1580 Specifications