TABLE OF CONTENTS
1 Safety rules and general safety guidelines ...................................... 5
2 Product identification data ................................................................ 5
3 Theory of operation ............................................................................ 6
4 Check of functions, initial start-up ................................................... 7
4.1 « Ex-FACTORY » parameters ...................................................................................................... 7
4.2 Setting the wireless enabling handle into service ..................................................................... 7
4.3 Setting the charger into service .................................................................................................. 8
4.4 Warning regarding the battery of the enabling handle .............................................................. 9
4.5 Setting up the product ............................................................................................................... 10
4.6 Testing the unit........................................................................................................................... 11
5 Setting the product into service ..................................................... 12
5.1 Electrical power supply, installation and wiring ...................................................................... 12
5.1.1 Receiver .................................................................................................................................................................. 12
5.1.2 Charger.................................................................................................................................................................... 12
5.2 Receiver antenna ........................................................................................................................ 12
5.3 Intervention mode and operation of enabling handle .............................................................. 13
5.3.1 Conditions for intervention in «monitoring - diagnostic» mode ................................................................................ 13
5.3.2 Conditions for intervention in « manual control » mode ........................................................................................... 14
5.3.3 Summary of conditions for intervention on machine. ............................................................................................... 14
5.3.4 Configuration of enabling handle operating mode ................................................................................................... 15
5.3.5 Receiver : selecting the program ............................................................................................................................. 15
5.3.6 Adjusting the machine area access time. ................................................................................................................ 16
5.4 Receiver : operation and wiring ................................................................................................ 17
5.4.1 Operation and wiring of function outputs ................................................................................................................. 17
5.4.2 Operation and wiring of safety relays K1-K2. ........................................................................................................... 18
5.4.3 Monitoring of main contactor : operation and wiring ................................................................................................ 19
5.4.4 Reset button : wiring and management ................................................................................................................... 19
5.4.5 Wiring of a wired safety shutdown device. ............................................................................................................... 20
5.4.6 Wiring of a machine area access authorisation request function. ............................................................................ 20
5.4.7 Wiring of an equipment with area access protection ............................................................................................... 21
5.4.8 Wiring of an equipment without area access protection .......................................................................................... 22
5.4.9 Wiring of “handle on charger” detection function ..................................................................................................... 22
5.4.10 Wiring of indicator light column on receiver ............................................................................................................. 23
5.4.11 Wiring of receiver power supplies ............................................................................................................................ 24
5.5 Charger : wiring and management. ........................................................................................... 25
5.5.1 Association of charger and wireless enabling handle .............................................................................................. 25
5.5.2 Wiring of charger power supply ............................................................................................................................... 25
5.5.3 Taking the wireless enabling handle off its charger ................................................................................................. 25
5.5.4 Setting the wireless enabling handle on its charger ................................................................................................. 25
5.6 Language selection .................................................................................................................... 26
5.7 Radio working frequency ........................................................................................................... 27
5.7.1 Selection of radio working frequency. ...................................................................................................................... 27
5.7.2 List of channels and radio frequencies (in accordance with enabling handle model) .............................................. 27
5.7.3 Reading the working frequency. .............................................................................................................................. 28
5.7.4 Changing the working frequency ............................................................................................................................. 28
5.8 Radio transmit power ................................................................................................................. 29
5.8.1 Transmit power selection ......................................................................................................................................... 29
(1) = The average range will depend on the product environment (presence of metal obstacles, …) ...................................... 29
5.8.2 Reading/changing the transmit power ..................................................................................................................... 29
5.9 Identity code ............................................................................................................................... 30
5.9.1 Identity code selection ............................................................................................................................................. 30
5.9.2 Reading the identity code, software version and SIM card serial number ............................................................... 30
5.9.3 Changing the identity code ...................................................................................................................................... 30
To Next Page
Loading...