Need help?Do you have a question about the JBL LSR6328P and is the answer not in the manual?
General| Woofer Size | 8 inches |
|---|---|
| Tweeter Size | 1 inch |
| Amplifier Power | 250 W |
| LF Amplifier Power | 200 W |
| HF Amplifier Power | 50 W |
| Input Connectors | XLR, TRS |
| Type | Active studio monitor |
| LF Driver | 8 inch low-frequency driver |
| HF Driver | 1 in. Titanium dome |
Read safety and operating instructions before using the product.
Retain instructions for future reference and troubleshooting.
Follow all warnings provided in the manual.
Adhere to all instructions given in the manual.
Product is for indoor use only; do not use near water.
Clean with a lint-free cloth; avoid solvent-based cleaners.
Do not block ventilation openings; install away from heat sources.
Protect power cords and grounding plugs; consult electrician if needed.
Use only attachments or accessories specified by JBL Professional.
Mounting by qualified persons; follow bracket manufacturer instructions.
Unplug apparatus during lightning storms or long periods of non-use.
Refer all servicing to qualified service personnel.
Use sturdy, well-balanced carts/stands; move with care.
Do not place naked flame sources on the apparatus.
Appliance coupler used as disconnect device must remain operable.
Explanation of warning symbols used in the manual.
Discusses features like LSR, RMC, Boundary Compensation.
Improves mid/high frequency accuracy at the listening position.
Zeroing out bass problems caused by room modes.
Restores accurate bass response when near walls or corners.
Enclosures reinforced for mounting with industry-standard brackets.
Approval for demanding production applications.
Details on Differential Drive, EOS Waveguide, etc.
Dual drive coils for higher output, less compression.
Contoured ports for accurate low frequency performance.
Electromagnetic braking reduces extreme excursion effects.
Improves transient response and reduces ear fatigue.
Provides targeted listening window for smooth spatial response.
High excursion capability for accurate reproduction.
Instructions on how to safely unpack the monitor units.
Guidance on stereo setup, listening distance, and speaker angles.
Discusses optimal orientation for LSR6328P and LSR6332.
Positioning speakers to face listener; woofer cone alignment.
Refer to individual model-specific instructions for connections.
Details on AC voltage, grounding, and input/output design.
Steps for powering up and setting listening levels.
Details on Neutrik Combi connector and input sensitivity settings.
Autosensing power supply; grounding requirements.
Switchable input sensitivity and trim control settings.
Switchable roll-off for low frequency extension and protection.
Shelf roll-off to compensate for placement near boundaries.
Shelf cut or boost for high frequency response.
Front panel LED indicates normal operation, clipping, or limiter.
Room Mode Correction controls for frequency, width, and depth.
Details on 5-way binding posts and bi-wiring options.
Adjustment for high frequency level to compensate for room acoustics.
Rotating the Mid/High sub-baffle for horizontal or vertical placement.
Room Mode Correction controls for frequency, width, and depth.
Details on XLR connectors, input sensitivity, and direct input.
Diagrams for stereo, ProLogic, and 5.1 channel system setups.
Using 1/4" jack for LCR bypass and discrete selection.
Factory set voltage; grounding requirements.
Input trim and switchable sensitivity settings.
Polarity reverse and bass alignment switches.
Low frequency adjustments for placement near boundaries.
Remote control for LCR bypass via 1/4" jack.
Front panel LED indicates operation status (Green, Amber, Red).
Room Mode Correction controls for adjustments.
Connecting balanced sources using XLR or TRS connectors.
Connecting unbalanced sources using twisted pair cable.
Connections using single conductor shielded cable with TRS plug.
Connections using unbalanced cable and TS to 1/4" input.
Details on using industry-standard mounting brackets.
Table detailing control positions for equalizer settings.
Frequency range, extension, and enclosure resonance.
Crossover point, distortion levels, and maximum SPL.
Calibrated input sensitivity, AC voltage, and connector.
Low/high frequency transducer components and amplifier specs.
Physical finish, volume, mounting points, weight, dimensions.
Nominal impedance, sensitivity, and frequency range.
Max power, recommended amp power, and crossover points.
Distortion levels at different SPLs and power compression.
Details on low, mid, high frequency transducers and amplifier.
Physical construction, mounting, weight, and dimensions.
Frequency range, extension, enclosure resonance, crossover.
Distortion, max SPL, and power compression.
Calibrated input sensitivity, user controls, and indicators.
Amplifier, transducer details, and physical specifications.
Details on warranty protection, coverage, and exclusions.
Procedure for obtaining warranty repair and contact information.
Limitations on implied warranties and exclusion of damages.
To Next Page
