How to reduce hum or buzz in JBL Speakers with long cables?
If you're experiencing hum or buzz with your JBL speakers, and it's due to an excessively long unbalanced cable run, try using the balanced outputs if they are available.
What to do if my JBL Speaker System has no sound but the speaker comes on?
If your JBL Speaker System powers on but produces no sound, here’s what to check: * Ensure that the signal source (mixer, instrument, etc.) is sending a signal. Check the VU meters on the source mixer and verify that any tape or CD is playing. Use headphones to confirm the instrument is sending an audio signal. * Inspect the cables and connections for faults. Disconnect and then re-seat the signal cables. If you suspect a cable is bad, replace it with one that is known to be working correctly.
What to do if my JBL Speakers sound distorted and the PEAK light is on?
If the signal from your JBL speakers sounds distorted and very loud, and the PEAK light is frequently on, it's likely due to an excessive input signal trying to exceed the speaker's capabilities. To resolve this, reduce the output level of the source.
How to fix JBL Speakers when there is no sound?
If there is no sound from your JBL speakers, make sure the speaker is connected to an active AC power source and that the circuit is on. Also, verify that the power is switched on and the power LED is illuminated.
Why is there noise or hiss coming from my JBL SRX812P Speakers?
If you hear noise or hiss at the output of your JBL speakers, the issue might be a noisy source device. Try disconnecting the devices connected to your speaker one at a time. If the noise disappears, the problem lies with the source or the connecting cable.
What to do if JBL SRX812P Speakers sound distorted at moderate volumes?
If the signal from your JBL speakers sounds distorted even at moderate volumes and the LIMIT light is not lit, the mixer or another source might be overdriven. Consult the owner's manual for your mixer and adjust the controls as needed.
Why is there no sound from my JBL SRX812P when using a microphone?
If you are getting no sound from your JBL speakers with a microphone directly connected, it could be that the microphone requires phantom power. Try switching to a dynamic microphone, using a battery-powered microphone if available, or using an external phantom power supply for condenser-type microphones.
Why do my JBL SRX812P have hum or buzz with improper gain?
If you're experiencing hum or buzz with your JBL speakers, it may be due to an improper system gain structure. Try reducing the input level controls and increasing the output level of your source devices.
Why does hum or buzz in JBL SRX812P change with mixer levels?
If the hum or buzz from your JBL speakers increases or decreases when the mixer level controls are moved, it could be due to an improper AC ground or faulty equipment connected to the mixer input. Disconnect or mute channels one at a time to isolate the problem. Refer to the owner’s manual of the faulty equipment for troubleshooting help.
What to do if the JBL Speaker System signal sounds distorted and very loud?
If the signal from your JBL Speaker System sounds distorted and the PEAK light is frequently lit, it indicates that the input signal is too high, exceeding the speaker's capabilities. Here’s what you can do: * Reduce the output level of the audio source. * Lower the level controls on the speaker itself. * Consider using additional SRX800 speakers to distribute the load.
Details safety and EMC compliance standards and test results.
Lists compliance specifications related to UL standards.
Outlines FCC compliance rules for device operation and potential interference.
Provides Industry Canada compliance information and warnings.
Lists items included in the speaker system packaging.
Illustrates various ways to set up the speaker system.
Details the general system type, output, and frequency characteristics.
Covers power rating, input impedance, and gain settings.
Lists driver details, coverage pattern, and crossover frequency.
Describes material, mounting, finish, dimensions, and weight.
Details the general system type, output, and frequency characteristics.
Covers power rating, input impedance, and gain settings.
Lists driver details, coverage pattern, and crossover frequency.
Describes material, mounting, finish, dimensions, and weight.
Details the general system type, output, and frequency characteristics.
Covers power rating, input impedance, and gain settings.
Lists driver details, coverage pattern, and crossover frequency.
Describes material, mounting, finish, dimensions, and weight.
Details the general system type, output, and frequency characteristics.
Covers power rating, input impedance, and gain settings.
Lists driver details, coverage pattern, and crossover frequency.
Describes material, mounting, finish, dimensions, and weight.
Details the general system type, output, and frequency characteristics.
Covers power rating, input impedance, and gain settings.
Lists driver details, coverage pattern, and crossover frequency.
Describes material, mounting, finish, dimensions, and weight.
Details the JBL 2432H 3-inch voice-coil compression driver.
Explains JBL's Differential Drive Technology ferrite drivers.
Describes the midrange driver derived from the VTX 20 system.
Discusses JBL's Progressive Transition Waveguides for high frequencies.
Explains network configuration and control via Audio Architect or SRX Connect.
Details the onboard DSP features including PEQs, delay, and presets.
Describes the Crown DriveCore technology and its power output.
Overview of the LCD screen's function for system control.
Describes how to access and adjust input levels and sensitivity.
Explains navigation to loudspeaker settings and presets.
Details how to access and view input meters for channels.
Explains how to configure IP, Subnet, and HiQnet addresses.
Describes where to find system model, version, and MAC address.
Standard tuning for full-range speakers without subwoofer.
Tuning optimized for stage monitor deployment.
Preset for enhanced speech intelligibility.
Tuning for SRX full-range speakers used with SRX subwoofers.
Tuning for SRX subwoofers used with SRX full-range speakers.
Tunings for use with subwoofers other than SRX818SP/SRX828SP.
Tunings for SRX subwoofers with other full-range speakers.
Presets for rear-facing subwoofers in cardioid systems.
Chart for selecting presets for sub/satellite configurations.
Overview of the onboard user-controllable DSP features.
Details DSP features compatible with JBL's V5 tunings.
Lists the comprehensive DSP capabilities available to users.
Control options via the proprietary SRX Connect app for mobile devices.
Advanced system configuration using Audio Architect software.
Connecting a single speaker directly to a computer via Ethernet.
Connecting multiple speakers to a network via router for control.
Connecting speakers wirelessly for network control, especially for tablets.
Detailed guide on using Audio Architect for SRX800 system control and setup.
Overview of the SRX Connect app for controlling SRX800 via mobile devices.
Guidance on positioning speakers for optimal audience coverage.
Advice on speaker placement to avoid feedback from microphones.
Recommendations to prevent low-frequency feedback from turntables.
Strategy for achieving better sound in challenging acoustic environments.
Guidelines for using speakers in PA and stage monitor configurations.
Defines who is covered under the JBL product warranty.
Specifies what types of damage and defects are covered by the warranty.
Outlines the cost responsibilities for warranty repairs.
Provides instructions on how to seek warranty service.
Discusses the duration limits for implied warranties.
Details damages that are not covered by the warranty.
JBL Professional's official mailing address for correspondence.
JBL Professional's shipping address for product returns or deliveries.
Contact details and hours for customer support.
Website address for accessing JBL Professional information.
Guidance on finding international distributors.
Step-by-step instructions for unboxing the speaker system.
Visual guide to various speaker setup configurations.
Highlights the main attributes and technologies of the SRX835P.
Chart for selecting presets for sub/satellite configurations.
To Next Page
General
