Jeep CJ-3A - Page 71

70
Pulley Speeds (R.P.M.) - 8” (20. 3CM.) Pulley
Power Take-Off Gear Ratios
Governor6-6 RATIO6-5 RATIO1-1 RATIO
ControlTRANSMISSIONTRANSMISSIONTRANSMISSIONEngine
PositionsSp~eds
LowHhInterHighLowInter.High
Inter.‘6
— Low ~.-
1 255 460 I 71436766310283065528571000
2306552857440795123436766210281200
335764510005149281440428 - 77412001400
4~-73711435871061164549088413721600
545982912856601193185155199515421800
6 510 9211428 734 1326 2057 j612110517142000
75611031157180714582262673123718852200
86121105111488115912468734132620572400
96631197185195417232674796143622282600
SPLINE SHAFT HORSEPOWER.
The chart below shows the draw bar horsepower at the governor controlled engine speeds and the horsepower at the spline
shaft with~ the vehicle stationary. Also is shown the horsepower available at the spline shaft with the vehicle at the maximum
approved weight (3500 lbs.) (1590 Kg.) moving at the speed shown and exerting a draw bar pull of zero pounds through 1200
pounds (544 Kg.) (maximum recommended) in steps of 300 pounds (136 Kg.).
H.P. at P.T.O. Spline Shaft
GovernedVehicle3500 Lb. Vehicle Moving with
EngineSpeedDraw BarVehicle _____—
R.P.M.M.P.H.*H.P.*~Stationary No Lbs.300 Lbs.600 Lbs.700 Lbs.1200 Lbs.
Draw BarDraw BarDraw BarDraw BarDraw Bar
Pull Pull Pull Pull Pull
10002.27.1815.412.811.09.37.55.7
12002.78.6218.316.214.012.09.87.8
14003.110.0623.319.617.114.712.19.6
16003.611.4927.122.920.117.414.411.5
18004.012.9330.926.323.019.916.713.5
20004.514.3833.029.125.621.918.414.8
22004.915.8033.031.727.823.820.016.0
24005.417.2433.1133.029.725.521.116.9
2600 5.8 18.68 33.0 33.0 31.4 26.7 I22.117.5
*Vehicle speed in low transmission and transfer case ratios.
**Based on maximum recommended draw bar pull for cantinuouu servnce-—1200 Lbs.
METRIC
Metric H.P. at P.T.O. Spline Shaft
GovernedVehicleDraw Bar1590 Kg. Vehicle Moving with
EngineSpeedH.P.~’Vehicle135 Kg.270 Kg.405 Kg.540 Kg.
R.P.M.K.P.H.~(Metric)Stationary DrawLrDraw BarDraw BarDraw BarDraw Bar
Pull Pull Pull Pull Pall
10003.57.2815.613.011.29.47.65.8
12004.48.7419.616.414.212.29.97.7
14005.010.2023.619.917.314.912.39.7
16005.811.6527.523.220.417.614.611.7
18006.413.1131.326.723.320.216.913.7
20007.214.5833.629.525.922.218.715.0
22007.916.0233.532.128.224.120.316.2
24008.717.4833.533.530.125.921.417.1
28009.318.9433.533.631.827.122.417.7
~Vehicle speed in low transmission and transfer case ratios.
1
’Based on maximum recommended draw bar mull for continuous service 640 Kg.
PDF created with pdfFactory trial version www.pdffactory.com