To Next PageTo Next PageWhy is my Jenn-Air Ranges oven not operating?
Your Jenn-Air Ranges oven might not be operating due to a programming error. Try switching the circuit breaker off to the oven for five minutes and then try the oven again. A power outage could be the cause; verify that power is present at the unit and the circuit breaker is not tripped. Also, the unit may be in Sabbath mode; refer to the Use & Care manual to remove the unit from Sabbath mode.
What to do if my Jenn-Air JES8750BA clock and timer are not working?
If the clock and timer on your Jenn-Air Ranges are not working, verify that power is present at the unit and the circuit breaker is not tripped, as the issue might be a power outage. Replace the household fuse, but do not increase the fuse capacity. Also, the electronic control might be locked; refer to the Use and Care manual and unlock the electronic control.
What to do if my Jenn-Air Ranges self-clean cycle is not working?
If the self-clean cycle on your Jenn-Air Ranges is not working, it might be due to a programming error. Try turning off the circuit breaker for five minutes and then try the oven again. Also, verify that the door lock energizes and engages.
Why is my Jenn-Air Ranges oven door not unlocking?
If your Jenn-Air Ranges oven door will not unlock, it may be because the oven is in self-cleaning mode. Allow the cycle to complete. Also, the oven may still be hot. It will not unlock until the unit has cooled to a safe temperature. Do not force the door open, as this will void the warranty. You can blow cool air on the door latch to quicken the process.
Why is the surface element on my Jenn-Air Ranges not heating?
If the surface element on your Jenn-Air Ranges isn’t heating, check for a loose wire connection or broken wire. Check the element for continuity and replace it if it has failed. Also, verify that all connections are clean and tight, and replace any broken wiring. A failed infinite switch could also be the cause; check the infinite switch and replace it if it has failed.
Why is the bake element not working on my Jenn-Air Ranges?
If there is no bake element operation on your Jenn-Air Ranges, it could be due to a loose wire connection or broken wire. Check the element for continuity and replace it if it has failed. Verify all connections are clean and tight, and replace any broken wires. Also, verify 240 VAC at the bake element.
Why is the broil element not working on my Jenn-Air JES8750BA?
If there is no broil element operation on your Jenn-Air Ranges, it could be due to a loose wire connection or broken wire. Check the element for continuity and replace it if it has failed. Verify all connections are clean and tight, and replace any broken wires. Also, verify 240 VAC at the broil element.
Why does my Jenn-Air Ranges oven light not operate?
If the oven light in your Jenn-Air Ranges does not operate, the oven lamp may have failed. Check the lamp and replace it if necessary. There may also be failed wiring, so check for broken, loose, or dirty connections. A failed light socket could also be the problem; check the light socket for continuity.
Why does my Jenn-Air JES8750BA Ranges oven smoke or have an odor when I use it for the first few times?
Minor smoking or odor is normal the first few times the Jenn-Air Ranges oven is used. Ventilate the area well and perform a self-clean cycle.
Lists model numbers covered by the manual.
Provides warnings for servicers and consumers regarding safe operation and electrical hazards.
Lists contact information for customer service and websites.
Explains the meaning of DANGER, WARNING, and CAUTION symbols.
General safety guidelines applicable to all appliances in the manual.
Specific safety precautions for using surface cooking units.
Safety precautions related to oven operation and usage.
Safety guidelines for operating the self-cleaning feature of the oven.
Precautions for cleaning and using glass/ceramic cooking surfaces.
Safety advice for maintaining and using ventilation hoods.
Procedures to follow in case of surface element or oven fires.
General safety advice and precautions for appliance use.
Explains the importance of not removing or altering safety devices.
Details the grounding connection for the oven frame and its importance.
Explains the coding system used for model identification and features.
Refers to individual technical sheets for detailed specifications.
Guidelines for properly placing the oven for optimal operation.
Instructions to keep air vents clear for proper oven cooling and function.
How to locate and record model and serial numbers for service.
Detailed instructions on properly grounding the appliance to prevent electrical shock.
Information on locating authorized service and ordering replacement parts.
Information on available extended service protection plans.
Identifies and labels the main parts of the range, including controls and oven cavity.
A table listing common problems, possible causes, and solutions for the range.
Explains the structure and meaning of fault codes for the Electronic Oven Control III.
Lists specific fault codes, their descriptions, and recommended troubleshooting steps.
Provides temperature vs. resistance data for oven sensors and meat probes.
Details how to test various components like elements, switches, and motors.
Continues detailed testing procedures for various range components like elements and limit switches.
Continues testing procedures for ribbon elements, infinite switches, temperature sensors, and fan motors.
Details testing procedures for downdraft motor, coil elements, ribbon elements, grill, and electronic control.
Outlines testing procedures for the switch membrane assembly on specific models.
Details switch membrane assembly testing for JES8850BC* and JES9750BA* models.
Details switch membrane assembly testing for JES9860BA*, JES9860BC*, and JES9900BC* models.
Details switch membrane assembly testing for JES9800BA* and JES9900BA* models.
Explains how to perform control reset and oven temperature adjustments.
Details how to set time options, language, C/F display, and auto convection.
Covers tone options, volume, energy saver, demo mode, service access, faults, versions, display test, and lockout.
Provides a chart showing relay activation for different cooking modes.
Instructions for entering and using the quick test mode for the oven control.
Provides resistance values for oven sensors and meat probes at various temperatures.
Repeats the description and structure of fault codes for the Electronic Oven Control III.
Steps for safely removing and reinstalling the entire range unit.
Instructions for removing cooktop cartridges on select models.
Steps for removing the main cooktop surface assembly.
Procedure for removing the control panel assembly from the range.
Steps for replacing the electronic control unit.
Instructions for removing and replacing infinite switches.
Procedure for removing the bottom access panel on select models.
Steps to remove and reinstall indicator lights from the control panel.
Instructions for replacing the meat probe receptacle in the oven cavity.
Procedure for removing the rear access panel of the range.
Steps for replacing the oven cooling fan.
Instructions for replacing the hidden bake element on select models.
Steps for replacing the standard bake element on select models.
Instructions for replacing the broil element.
Procedure for removing the downdraft blower motor on select models.
Steps for removing the convection motor assembly.
Instructions for replacing the convection heating element.
Procedure for replacing the oven temperature sensor.
Steps for replacing the oven light bulb and socket.
Instructions for removing the oven vent or smoke eliminator.
Steps for replacing the oven hi-limit thermostat.
Instructions for replacing the oven door latch mechanism.
Steps for removing the warming drawer from the range.
Instructions for replacing the warming drawer heating element.
Steps for replacing the hi-limit switch for the warming drawer.
Procedure for safely removing the oven door from the range.
Instructions for removing the oven door hinges.
Steps for disassembling the oven door itself, including glass and components.
Steps for disassembling the warming drawer unit.
Instructions for removing and disassembling the warming drawer tracks.
An exploded view diagram showing parts for oven door, warming drawer, and access panel.
Directs users to customer installation literature or website for specific model installation.
Details electrical connection requirements, codes, and procedures for the range.
Specifies required clearances around the range for installation and safety.
Provides detailed dimensional drawings and clearance requirements for installation.
Describes different vent location choices and their corresponding installation steps.
Step-by-step instructions for installing rear wall ventilation for the blower motor.
Step-by-step instructions for installing floor venting for the blower motor.
Step-by-step instructions for installing side venting for the blower motor.
Guides for adjusting the blower motor mounting bracket for proper installation.
Continues instructions for side venting installation, including bracket rotation and spacer use.
Details different options for connecting the range using conduit or service cords.
Helps identify different types of electrical outlets and connections needed for the range.
Step-by-step guide for connecting the range using a 3-wire electrical connection.
Step-by-step guide for connecting the range using a 4-wire electrical connection.
Instructions for a 3-wire connection using bare wires and torque specifications.
Instructions for a 4-wire connection using bare wires.
Continues installation steps for connecting ductwork to the range and blower.
Continues installation steps for connecting ductwork to the range and blower.
Covers final checks, filter installation, access panel replacement, and power-up.
Directs users to customer use and care literature for specific model information.
Title page for the Use & Care Guide for the Jenn-Air Electric Downdraft Slide-In Range.
Instructions and precautions for operating the self-clean cycle and cleaning the oven.
Information on what to expect after a self-clean cycle and how to handle residual soil.
General guidelines for cleaning specific parts like the access panel, control panel, and knobs.
Detailed cleaning instructions for cooktop glass, oven window, interior, racks, and stainless steel surfaces.
Instructions for cleaning grill accessories, elements, grates, grease cups, and thawing foods.
Explains how to use surface controls, suggested heat settings, and broiling.
Overview of the oven control panel, its functions, and quickset pads.
Instructions for setting and adjusting the clock, day of week, and time format.
How to change display language and temperature scale (C/F) and auto convection settings.
Explains how to manage timers, adjust beeps, set volume, and lock the control panel.
How to disable the 12-hour shutoff and enable the energy saver display feature.
Information on accessing service contact numbers and the product demo mode.
Instructions for setting the bake function, including temperature and preheating.
Details on using Cook & Hold and Delay features for baking.
Explains convection cooking principles and how to use Convect Bake, Roast, and Pastry.
Instructions for using the rapid preheat feature to reduce baking times.
Specific procedures for setting Convect Roast and Convect Pastry cooking modes.
Instructions for using More Options, Cook & Hold, Delay, and Proofing features.
How to use the Keep Warm feature for food and plates.
Detailed instructions on using the meat probe for accurate roasting results.
A table listing recommended internal temperatures for various meats and poultry.
Instructions for using the drying function, including door adjustments and drying times.
How to select, save, create, edit, and delete favorite recipes.
Explains how to access and use the Setup menu for clock, language, C/F, and auto convection settings.
Instructions for activating, deactivating, and using the Sabbath Mode for baking.
How to adjust oven temperature and set voltage for optimal performance.
How to adjust beep tones, timer alerts, and overall volume levels.
Information on 12 HR Shutoff, Energy Saver, Service, and Demo modes.
General
