Jenn-Air JXT8030ADS User Manual (English)

Other manuals for Jenn-Air JXT8030ADS

User Guide24 pages

Installation Guide8 pages

Questions and Answers:

M
Melvin PetersonAug 11, 2025
Why won't the blower motor and lights turn on in my Jenn-Air JXT8030ADS Ventilation Hood?
- A
  Anne KramerAug 11, 2025
  If the blower motor and lights aren't working on your Jenn-Air Ventilation Hood, here are a few things to check: * Make sure the unit is getting 120 VAC of input power. * Check that the circuit breaker hasn't tripped. * Ensure all black/white or white wires are tightly connected to the control board; also, check if any wires are disconnected from the control board. If these steps don't resolve the issue, the control board or touch pad/control panel might be defective. In that case, perform a control board test or touch pad/control panel test.
E
ewarnerAug 17, 2025
What to do if the Jenn-Air JXT8030ADS lights are on but the blower motor won't work?
- G
  Gregory FletcherAug 17, 2025
  If the lights on your Jenn-Air Ventilation Hood are on, but the blower motor isn't working, consider the following: * Check the blue wire connection on the control board to ensure it's secure. * Make sure the blower motor isn't stuck or blocked by anything, and that it can rotate freely. * The blower motor may be too hot and shut down by the thermal protection system, so allow the blower motor to cool. If these steps don't fix the problem, the blower motor or capacitor might be defective, requiring a test. Also, the touch pad or control panel could be defective and require testing.
G
Gabriel KingAug 23, 2025
Why does my Jenn-Air JXT8030ADS Ventilation Hood light illuminate at full brightness only?
- D
  Dean AndersonAug 23, 2025
  If the lights on your Jenn-Air Ventilation Hood only illuminate at full brightness, there might be loose wires at the light socket or control board. Make sure all wires are securely connected. The light socket, control board, or control panel could also be defective. Perform a halogen light test, control board test, or touch pad/control panel test. In some cases, the control panel may need to be replaced.
B
bwrightAug 29, 2025
What to do if the Jenn-Air JXT8030ADS Ventilation Hood blower motor operates, but I cannot change the fan speed?
- T
  Terry LewisAug 29, 2025
  If the blower motor in your Jenn-Air Ventilation Hood is running but you can't adjust the fan speed, it could be due to several reasons: * A shorted or defective capacitor. * A defective blower motor. * A defective touch pad or control panel. * Obstructions in the blower motor. You should perform a capacitor test, blower motor test, or touch pad/control panel test. Also, make sure there are no obstructions in the blower motor that prevent it from operating correctly.
J
Justin ValdezSep 4, 2025
Why does my Jenn-Air JXT8030ADS blower motor start slowly and not reach full speed?
- L
  Louis CaseySep 5, 2025
  If your Jenn-Air Ventilation Hood's blower motor starts slowly and doesn't reach full speed, the issue could be: * A shorted or defective capacitor. * A defective blower motor. * A defective control board. * Obstructions in the blower motor. Consider performing a capacitor test, blower motor test, or control board test. Also, check for any obstructions that might be preventing the blower motor from operating freely.

Jenn-Air JXT8030ADS Specifications

General

Brand	Jenn-Air
Model Number	JXT8030ADS
Product Type	Ventilation Hood
Appliance Category	Ventilation
Type	Wall Mount
Width	30 in
Lighting	Yes
Lighting Type	LED
Number of Bulbs	2
Touch Controls	Yes
Finish	Stainless Steel
Number of speeds	3
Number of Fan Speeds	3
Installation Type	Wall Mount
CFM (Air Flow)	600 CFM
Control Type	Electronic
Filter Type	Grease