JR300 JR400 JR500
Owner's Manual
Introduction
Thank you for choosing this JENSEN Universal Remote Control. The new JENSEN line of universal remotes has been
designed with the consumer in mind. Months of market research and focus groups helped develop an ergonomically
correct remote control with all the latest features and benefits to enhance your viewing experience.
Before you begin using your new JENSEN remote control, you must first read the instructions carefully and install
a set of two “AA” batteries (not included). This manual was written for use with the JR300, JR400, and JR500.
Please note that not all modes will be available in all models.
Installing The Batteries:
1. Locate the battery cover on the back of the remote control.
2. Pull down the lever on the battery door to open battery compartment.
3. Install two “AA” batteries, making sure that the “+” and “-“ marks on the batteries match the diagram inside
the battery compartment.
4. A battery test can be performed by pressing any of the
“mode keys”: TV, VCR, CBL/SAT/ANT
(cable/satellite/antenna), DVD, and Audio. The red LED indicator will blink once.
Note: Your JENSEN Universal Remote Control has a built-in memory backup that allows you to remove the
batteries for up to 10 minutes without losing programmed information. If you wait longer than 10 minutes
to replace the batteries, you may have to reprogram your universal codes.
Programming the Remote Control:
There are two methods available to program your new remote control. The first method is “Manual Programming;”
the second method is “Standard Step-and-Set.” Please choose which of the following best fits your needs.
Manual Programming:
Locate the four-digit codes for your device and brand in the code listing included with this manual. You will notice
that there will be more than one four-digit code for some devices next to some brands. This is the result of many
manufacturers using different codes for different models. Once you have located the codes that you will be using,
you are ready to start programming your remote. Please follow the steps below for best results.
1. Manually turn on the device that you are trying to set up (TV, VCR, Cable/Satellite/Antenna, DVD, or Audio)
2. Press down and release the device
“mode key” (TV, VCR, CBL/SAT/ANT, DVD, or AUD) on the remote control.
The red LED indicator will blink once.
3. Press down and hold the
SETUP key until the red LED indicator blinks twice, then release.
4. Enter the first four-digit code for the device you are trying to program. The LED will blink once on each digit
entry except for the last digit, where it will blink twice to confirm that a valid code has been programmed.
5. Aim the remote control at the device that you programmed and press
POWER. If the device turns off, you have
programmed the correct code. If the device does not turn off, return to step 2 and use the next four-digit code
for that brand and model.
6. Repeat the steps above to program the next device.
• If any other key is pressed besides a digit key during programming, the unit will display one long blink, exit
programming state, and restore the last preprogrammed code.
• Upon entry of an invalid key sequence or invalid code, the remote control will display one long blink and return
to the last preprogrammed code.
• The unit will exit programming state and return to the last preprogrammed code if 10 seconds have elapsed
between digit entries.
Standard Step-and-Set Programming:
If the device code for a particular brand is unknown, you will be able to cycle the remote through the available codes
for that device mode and sample functions from each code in order to find the code that operates the desired
device. The keys which are available to be sampled (provided they are applicable to that mode) are: 0, 1, 2, 3,
POWER, CHANNEL UP, VOLUME UP, PLAY and STOP. Invalid key presses will be ignored while in the programming
state. Follow the steps below to cycle through each available device code and sample its functions.
1. Manually turn on the device that you are trying to set up (TV, VCR, Cable/Satellite/Antenna, DVD, or Audio).
2. Press down and release the device
“mode key” (TV, VCR, CBL/SAT/ANT, DVD, or AUD) on the remote control.
The red LED indicator will blink once.
3. Press down and hold the
SETUP key until the red LED indicator blinks twice, then release.
4. Enter the digits
9, 9, 1. The red LED will blink twice. Press the first function you want to test, i.e., POWER. If
the device turns off, you have located the correct code. If the device does not turn off, press the
“mode key”
again to go to the next code in the library. Repeat the procedure above until locating the correct code or until
you have gone through the entire code library.
5. When the correct code has been located, press
SETUP and release. The red LED will blink twice, locking
in the code for that device.
6. Repeat the steps above to program the next device.
Note: The available functions within a code may be sampled as many times as desired until advancing to the next
code by pressing a specific device mode key. For the selected mode, the search will begin with the most
popular device code when no code is currently programmed or will begin with the current programmed code.
The search function has an end of cycle designator (LED will blink three times) to indicate when a cycle has
been completed. The unit will begin to cycle through the available codes again. The LED will light each time
a function is sent. If no key is pressed within 10 seconds, the remote will exit the setup mode and return
to the code previously set up before Step-and-Set was initiated. The unit will blink two times after successful
completion of the programming sequence.
• Upon entry of an invalid key sequence, the LED will display one long blink and return to normal operation.
• The unit will exit programming state and return to normal operation if 10 seconds have elapsed between
key presses.
Code Verification:
To find the four-digit device code that you have programmed in the remote, follow the procedure outlined below.
This is used to get feedback on the device code selected. The number of blinks that occur after pressing the
numeric keys 1,2,3 and 4 represents the 4-digit ID code set up for that mode. There is a 0.5-second delay
between each blink. There is also a 0.5-second time delay after each key press.
1. Press down and release the device
“mode key” (TV, VCR, CBL/SAT/ANT, DVD or AUD) on the remote control.
2. Press down and hold the
SETUP key until the red LED blinks twice, then release.
3. Enter the digits
9, 9, 0. The red LED indicator will blink twice. Press numbers 1, 2, 3, and 4, observing the
number of blinks after each number has been pressed. Write down the number for future use.
Note: The digit “0” will not blink.
Using Your JENSEN Remote Control:
After you have programmed the JENSEN Universal Remote Control for use with one or more devices, you are ready
to start using the remote. Follow the steps below to get acquainted with your remote.
1. Press the mode key of the component that you want to control (TV, VCR, CBL/SAT/ANT, DVD, or AUD).
2. Press the
POWER key to turn on the component if it is not already on.
3. Press the key of the function you wish to perform. (See
Key Function Diagram
for a complete listing of key
descriptions.)
ONE YEAR WARRANTY
Recoton Corporation (“Company”) warrants to the original retail purchaser of this product that should the product or any part thereof
be proven defective in material or workmanship within one year from the date of original purchase, such defects will be repaired or
replaced, at the Company’s option, without charge for parts or labor.
To obtain replacement within the terms of this warranty, the product should be delivered, transportation prepaid, to the Dealer where
purchased or to the Company, along with proof of date of purchase. Call 1-800-RECOTON to obtain information regarding the proce-
dure for proper return of your product, if your Dealer does not honor the warranty. This warranty is valid in the USA and Canada only.
THIS WARRANTY DOES NOT APPLY TO ANY PRODUCT OR PART THEREOF WHICH HAS BEEN DAMAGED
THROUGH ALTERATION, MISHANDLING, MISUSE, NEGLECT, ACCIDENT, IMPROPER INSTALLATION OR
UNAUTHORIZED REPAIR.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY AND ALL OTHER WARRANTIES, EXPRESSED OR
IMPLIED, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE AND ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY
IN CONTRACT OR TORT, WHETHER OR NOT ARISING FROM THE COMPANY’S NEGLIGENCE, ACTUAL
OR IMPUTED. NO PERSON OR REPRESENTATIVE IS AUTHORIZED TO ASSUME FOR THE COMPANY ANY
OTHER LIABILITY IN CONNECTION WITH THE SALE OF THIS PRODUCT. IN NO EVENT SHALL COMPANY
BE LIABLE FOR INDIRECT INCIDENTAL OR CONSEQUENTIAL DAMAGES.
This warranty gives you specific legal rights and you may also have other rights which vary from state
to state/province to province, so some of the above limitations or exclusions may not apply to you.
NON-WARRANTY SERVICE
If non-warranty service is required, the product may be sent to the Company for repair/ replacement, transportation prepaid, by calling
1-800-RECOTON for details, complete instructions, and service fee charges.
AD39025 11/02
Channel Scan searches by using two methods: sending the Channel Up command (if found), and by sending the
digits 0-9 for repeat cycling for a maximum of 10 iterations. The
modes available for Channel Scan are TV, VCR,
CABLE, SATELLITE and DVD.
Note: If above MODES have been reassigned, Channel Scan is still valid. For example, if the TV has been reassigned
to VCR (TV2), pressing <TV2> <SCAN> will cause Channel Scan to activate. If a mode which does not allow
Channel Scan has been reassigned, i.e., VCR (CD2), pressing <CD2> <SCAN> will not cause Channel Scan to
activate, because CD is an invalid Channel Scan mode.
Sleep Timer
In the TV, SATELLITE, DVD and CABLE modes, the remote’s built-in sleep timer will be activated by pressing the
SLEEP key when the target device ID does not have a code for sleep. The first press of the SLEEP key will activate
a 15-minute timer. Additional key presses within 10 seconds will increase the timer value in 15-minute increments,
up to a maximum of 60 minutes. Fifth and subsequent key presses will be ignored and the timer will remain at 60
minutes.
Each key press is acknowledged by a series of blinks indicating how many increments have been programmed.
For example: one blink for the first press, two blinks for the second press, etc.
Sleep timer activates 10 seconds after the last press of the
SLEEP key. The visible LED will blink approximately once
every 15 seconds to indicate that the timer is running. When running, the sleep timer is automatically canceled if
any other key on the keypad is pressed. Pressing the sleep key itself initializes the timer sequence to 15 minutes.
When the timer expires, the remote sends the target device’s power function, or power off when separate power
on and off commands exist.
If your device has a sleep timer function, you may still enable the built-in sleep timer by following the steps outlined
below.
1. Press the
“mode key” of the component for which you want to set the sleep timer (TV, VCR, CBL/SAT/ANT,
or DVD).
2. Press down and hold the
SETUP key until the red LED indicator blinks twice, then release.
3. Enter the digits
9, 7, 0. The red LED indicator will blink twice.
4. Press the
SLEEP key once for 15 minutes, twice for 30 minutes, three times for 45 minutes and four times
for 60 minutes.
Resetting Sleep Timer to Factory Default
1. Press down and hold the SETUP key until the red LED blinks twice, then release.
2. Enter the digits
9, 7, 0. The red LED indicator will blink four times, indicating that the sleep timer has been
reset to the factory default.
Note: If the TV, SATELLITE or CABLE modes have been reassigned, Sleep Timer is still valid provided it is set up
on the logical mode. For example, if the TV has been reassigned to VCR (TV2), TV2 is programmed for
Sleep Timer. Pressing <TV2> <SLEEP> will cause Sleep Timer to activate.
Low Battery Condition
When the batteries installed in the remote become low on power, the remote will enter in a LOW BATTERY
CONDITION. While in the low voltage condition, the unit will not operate. This is to protect RAM and user
settings. When new batteries are installed, full operation will be restored. The typical duration is 10 minutes.
Stuck Key Time Out
The remote will stop transmitting IR to conserve power upon any key depressed for longer than 30 seconds.
Customer Info Line Línea telefónica de información al cliente:
Toll Free 1-800-962-3986 Línea gratuita de teléfono al: +1-800-962-3986 en EE.UU.
Key Description:
1. Red LED Indicator – This light will turn on or
blink depending on the function that you are
performing. The instructions in this manual
will explain the normal operation.
2. POWER – Turns the selected device
on or off.
3. SCAN – Automatically changes channels
every 3 seconds.
4. TV/VCR – Selects inputs on TV, VCR,
Cable/Satellite, or DVD.
5. CHANNEL UP (Skip Forward) – Press this
key to move up one channel. When in DVD
or CD mode, press this key to move up one
track.
6. FAST FORWARD – Fast-forwards
a videotape, CD, or DVD.
7. PLAY – Press this key to start or resume
playing videotape, CD or DVD.
8. STOP – Press this key to stop the playback,
recording, rewinding or fast-forwarding of a
videotape. In CD or DVD mode, press this
key to stop the playback of a CD or DVD.
9. CHANNEL DOWN (Skip Back) – Press this
key to move down one channel. When in
DVD or CD mode, press this key to move
down one track.
10. LAST – Also known as “channel recall.”
Press this key to switch to the last channel
that you were viewing. In CD or DVD mode,
press this key to repeat a CD or DVD track
or for random play.
11. RECORD – Press this key to start recording
a program.
Note: As an added safety feature, you must
press the RECORD key twice in order to start
recording.
12. MUTE –
Press this key to mute the sound.
13. VOLUME (-) – Press this key to decrease
the volume level.
14. PAUSE – Press this key to pause the
recording or playback of a videotape.
Press again to resume recording or play-
back. In CD or DVD mode, press this key to
pause the playback of a CD or DVD.
15. REWIND – Press this key to rewind
a videotape, CD or DVD.
16. VOLUME UP (+) – Press this key to increase
the volume level.
17. SLEEP – Press this key to activate the
automatic sleep timer.
18. FAVORITE CHANNEL – Press this key to access
favorite channel mode of Cable Box and
Satellite Receiver.
19. INFO – Press this key to access the on-
screen information menu function of the
TV, VCR, Cable Box, Satellite Receiver,
or DVD player.
20. MENU – Press this key to access the
on-screen menu of the TV, VCR, Cable
Box, Satellite Receiver, or DVD.
21. Menu Right ( ) – Press this key to navigate
on-screen menu functions to the right.
22. Menu Down ( ▼ ) - Press this key to
navigate on-screen menu functions down.
23. SELECT – Press this key to select an option
while in on-screen menu mode.
24. Menu Left ( ) - Press this key to navigate
on-screen menu functions to the left.
25. Menu Up ( ▲ ) - Press this key to navigate
on-screen menu functions up.
26. GUIDE - Press this key to access the on-
screen menu guide function of the Cable Box,
Satellite Receiver, and some CD players.
27. EXIT – Press this key to exit the on-screen
menu display.
28. 0 – 9 Keys – Press these keys for direct key
entry. In CD or DVD mode, press these keys
to select a track. In Receiver mode, press
these keys to select source input.
29. ENTER – In menu mode, press to select
an option. Otherwise, press this key to enter
in a channel. In CD or DVD mode, press this
after entering a track number.
30. SETUP – Press this key to enter the setup
mode.
31. Mode Keys (TV, VCR, CBL/SAT/ANT, DVD
and AUD) –
Press these keys to select device
mode (TV, VCR, Cable/Satellite/ Antenna,
DVD, or Audio).
NOTES: 1. Volume and Mute will punch through to TV by default. When the volume is unlocked,
all the devices will have their own volume if their ID has volume data.
2. Will punch through to VCR
.
Key Function Diagram:
JR500 featured
Additional Remote
Control Features:
Record
To prevent accidental recording over videotape,
the new line of JENSEN remotes requires that the
RECORD key be pressed twice in order to begin
recording.
Mode Reassignment
This feature allows you to reassign a selected
device mode key (TV, VCR, CBL/SAT/ANT, DVD
or AUD) to the desired device mode key. For
example, a VCR device mode key (destination
mode) can be changed to an additional TV device
mode key (source mode) to facilitate the operation
of two different TVs. Follow the steps below for
best results.
1. Press down and hold the
SETUP key until
the red LED blinks twice, then release.
2. Enter the digits
9, 9, 2. The red LED indicator
will blink twice.
3. Press the source
“mode key”, i.e., TV, VCR,
CBL/SAT/ANT, DVD or AUD.
4. Press the destination
“mode key”, i.e., TV,
VCR, CBL/SAT/ANT, DVD or AUD.
Note: The ID in the destination mode now is the
default ID of the source mode, i.e., VCR
mode could become TV2. The unit will blink
twice after successful completion of the
programming sequence.
5. Pressing the same mode key twice after entering
9, 9, 2, will return key to original mode.
Volume Lock/Unlock
Note: This feature does not apply to any device
keys which have been copied using the key copier
feature.
The volume controls (
VOLUME ▲, VOLUME ▼ and
MUTE) on the remote can be configured in one of
three ways:
1. They can be assigned to control a single device
regardless of which device mode key is
pressed. For example, if the volume controls
are "locked" to the TV, pressing the volume
controls will adjust the TV volume even if the
remote is in
VCR mode.
2. The controls can control each individual device.
For instance, the volume controls will adjust
the TV volume when the remote is in TV mode,
and the cable (or satellite) volume when in
CBL/SAT mode.
3. The volume controls can be assigned to control
a single device (as in the first example) then
"unlocked" for individual device modes you
choose. For example, you want the volume
controls to affect only the TV if you are in the
TV or VCR modes, but you want the volume
controls to affect your cable box if you change
to the
CBL/SAT mode.
Note: The remote ships from the factory with the
volume controls assigned to control the TV regard-
less of selected device mode (case 1 above).
To "unlock" the volume controls (case 2 above):
1. Press and hold the SETUP key until the red
LED light blinks once, pauses and blinks twice
more. Then release the key.
2. Enter the digits
9, 9, 3. The red LED light will
blink twice after pressing the
3 key.
To "lock" the volume controls to a particular device
(case 1 above):
1. Press and hold the SETUP key until the red LED
light blinks once, pauses, and blinks twice
more. Then release the key.
2. Enter the digits
9, 9, 3. The red LED light will
blink twice after pressing the
3 key.
3. Press the device key (e.g.
TV, VCR, CBL/SAT)
for the device you want to assign the volume
controls to. The red LED will blink four times
to confirm the volume controls are locked.
To "unlock" the volume controls for a particular
device (case 3 above):
1. Press the DEVICE key for the mode you wish
to unlock.
2. Press and hold the
SETUP key until the red LED
light blinks once, pauses, and blinks twice
more. Then release the key.
3. Enter the digits
9, 9, 3. The red LED light will
blink twice after pressing the 3 key.
4. Press the
VOLUME ▼ key. The red LED will blink
four times the volume controls have been
unlocked for that mode.
Channel Scan
For convenient “channel surfing,” press the SCAN
key. This activates the remote to change channels
once every three seconds until any key is pressed
or until 100 channel changes occur.
Mode 1 Mode 2 Mode 3 Mode 4 Mode 5
Key Label TV VCR Recoton Antenna SAT CBL DVD CD Amp Tuner
(JR300, 400, 500) (JR300, 400, 500) (JR300, 400, 500) (JR300, 400, 500) (JR300, 400, 500) (JR 400, 500) (JR500) (JR500) (JR500)
Setup Setup Setup Setup Setup Setup Setup Setup Setup Setup
POWER Power Power Power Power Power Power Power Power Power
TV
*
--- --- --- --- --- --- --- ---
VCR ---
*
--- --- --- --- --- --- ---
CBL/SAT/ANT --- ---
***
--- --- --- ---
DVD --- --- --- --- ---
*
--- --- ---
AUDIO --- --- --- --- --- ---
** *
GUIDE --- ------- Rotate Left GUIDE GUIDE --- Random Balance left
MENU MENU MENU Rotate Right MENU MENU MENU --------- SUP Balance Right
INFO INFO ------- Memory INFO INFO INFO --------- Delay + Delay +
EXIT Exit Exit Clear Exit Exit Exit --------- Delay - Delay -
UP UP UP Right Dipole Left UP UP UP --- SU+
DOWN Down Down Right Dipole Right Down Down Down --- SU-
LEFT Left Left Left Dipole Left Left Left Left --- Balance left R Rear -
RIGHT Right Right Left Dipole Right Right Right Right --- Balance Right R Rear +
SELECT Select Select --- Select Select Select --- Select Select
VOL+ VOL+ VOL+(1) --- VOL+ (1) VOL+ (1) VOL+ (1) --- VOL+ VOL+
VOL- VOL- VOL- (1) --- VOL- (1) VOL- (1) VOL- (1) VOL- VOL-
CH+ CH+ CH+ --- CH+ CH+ Skip Forward Skip Forward CH+ CH+
CH- CH- CH- --- CH- CH- Skip Reverse Skip Reverse CH- CH-
MUTE MUTE MUTE(1) --- MUTE(1) MUTE(1) MUTE(1) -------- MUTE(1) MUTE(1)
LAST PREVIOUS CHANNEL PREVIOUS CHANNEL PREVIOUS CHANNEL PREVIOUS CHANNEL Repeat Repeat
Digit 1 DIGIT 1 DIGIT 1 DIGIT 1 DIGIT 1 DIGIT 1 DIGIT 1 DIGIT 1 Tuner Tuner
Digit 2 DIGIT 2 DIGIT 2 DIGIT 2 DIGIT 2 DIGIT 2 DIGIT 2 DIGIT 2 LD LD
Digit 3 DIGIT 3 DIGIT 3 DIGIT 3 DIGIT 3 DIGIT 3 DIGIT 3 DIGIT 3 DSP Mode DSP Mode
Digit 4 DIGIT 4 DIGIT 4 DIGIT 4 DIGIT 4 DIGIT 4 DIGIT 4 DIGIT 4 FM Mono FM Mono
Digit 5 DIGIT 5 DIGIT 5 DIGIT 5 DIGIT 5 DIGIT 5 DIGIT 5 DIGIT 5 3 channel logic 3 channel logic
Digit 6 DIGIT 6 DIGIT 6 DIGIT 6 DIGIT 6 DIGIT 6 DIGIT 6 DIGIT 6 AUX AUX
Digit 7 DIGIT 7 DIGIT 7 DIGIT 7 DIGIT 7 DIGIT 7 DIGIT 7 DIGIT 7 TV TV
Digit 8 DIGIT 8 DIGIT 8 DIGIT 8 DIGIT 8 DIGIT 8 DIGIT 8 DIGIT 8 Phono Phono
Digit 9 DIGIT 9 DIGIT 9 DIGIT 9 DIGIT 9 DIGIT 9 DIGIT 9 DIGIT 9 ANT ANT
Digit 0 DIGIT 0 DIGIT 0 DIGIT 0 DIGIT 0 DIGIT 0 DIGIT 0 DIGIT 0 CD CD
ENTER ENTER ENTER --- ENTER/SELECT ENTER/SELECT ENTER ----- --- -------
TV/VCR TV/VIDEO TV/VCR A/B BYPASS-TV/DSS/TV/SAT A/B TV/VCR A-B --- Band
SCAN SCAN SCAN SCAN SCAN SCAN Scan Scan Scan Scan
SLEEP Sleep ---- --- --- SLEEP ---- ---- ---
FAV Channel ------- ---- --- FAV Channel FAV Channel ---- ---- ---
REW Punch to VCR(2) REWIND --- --- --- REWIND REWIND REW REW
PLAY Punch to VCR(2) PLAY --- --- --- PLAY PLAY PLAY PLAY
FFWR Punch to VCR(2) FFWD --- --- --- FFWD FFWD FFWR FFWR
REC Punch to VCR(2) RECORD --- --- --- ---- REC REC REC
STOP Punch to VCR(2) STOP --- --- --- STOP STOP STOP STOP
PAUSE Punch to VCR(2) PAUSE --- --- --- PAUSE PAUSE PAUSE PAUSE
Functional Key Chart
1. Red LED Indicator
18. Favorite Channel
17. Sleep
16. Volume Up (+)
15. Rewind
14. Pause
13. Volume Down (-)
12. Mute
11. Record
27. Menu Exit
26. Menu Guide
25. Menu Up
24. Menu Left
23. Select
30. Setup
2. Power
3. Scan
4. TV/VCR
5. Channel Up
(Skip Forward)
6. Fast Forward
7. Play
8. Stop
9. Channel Down
(Skip Back)
10. Last
19. Menu Info
20. Menu
21. Menu Right
22. Menu Down
28. 0-9 Keys
29. Enter
31. Mode Keys:
TV, VCR,
CBL/SAT/ANT,
DVD and AUD
*Highlighted Keys are used
for on-screen menu control.
GARANTÍA POR UN AÑO
Recoton Corporation (la "Compañía") garantiza al comprador minorista original de este producto que si el producto o cualesquiera de
sus partes estuvieran defectuosas en cuanto al material o su fabricación, dentro del año a partir de la fecha de compra original, dichos
defectos serán reparados o repuestos, a criterio de la Compañía, sin cargo alguno por las piezas o mano de obra.
Para obtener el repuesto dentro de los términos de esta garantía, el producto deberá ser enviado, con envío prepagado, al Distribuidor
donde fue adquirido o a la Compañía, junto con el comprobante de fecha de compra. Sírvase llamar al +1-800-RECOTON para obtener
más información acerca del procedimiento adecuado de devolución de su producto, si su Distribuidor no se apega a las condiciones de
esta garantía. Esta garantía es válida únicamente en los EE.UU. y Canadá.
ESTA GARANTÍA NO ES APLICABLE AL PRODUCTO O PIEZA DEL PRODUCTO QUE HAYAN SIDO DAÑADOS
POR ALTERACIONES, MAL MANEJO, MAL USO, NEGLIGENCIA, ACCIDENTE, INSTALACIÓN INADECUADA O
REPARACIÓN NO AUTORIZADA.
ESTA GARANTÍA ES EXCLUSIVA Y REEMPLAZA A CUALQUIERA Y TODAS LAS DEMÁS GARANTÍAS, EXPRE-
SAS O IMPLÍCITAS, INCLUIDAS A MANERA DE EJEMPLO, LAS GARANTÍAS IMPLÍCITAS DE COMERCIABILI-
DAD Y ADECUACIÓN A LOS FINES ESPECÍFICOS Y A CUALQUIER OBLIGACIÓN, RESPONSABILIDAD, DERE-
CHO, RECLAMACIÓN O RECURSO CONTRACTUAL O EN MATERIA DE HECHOS ILÍCITOS, YA SEA QUE
SURJA O NO DE LA NEGLIGENCIA, REAL O IMPUTADA, DE LA COMPAÑÍA. NINGUNA PERSONA O REPRE-
SENTANTE ESTÁ AUTORIZADO A ASUMIR EN NOMBRE DE LA COMPAÑÍA NINGUNA OTRA RESPONSABILI-
DAD EN RELACIÓN CON LA VENTA DE ESTE PRODUCTO. EN NINGÚN CASO LA COMPAÑÍA SERA RESPON-
SABLE DE LOS DAÑOS INCIDENTALES O INDIRECTOS.
Esta garantía le otorga derechos legales específicos y otros derechos que pueden variar de un estado a
otro, de una provincia a otra, de manera que algunas de las limitaciones o exclusiones antes mencionadas
no se aplicarán a su caso.
SERVICIO SIN GARANTÍA
Si se requiere un servicio sin garantía, puede enviar el producto a la Compañía para su reparación/cambio, con envío prepagado, lla-
mando al +1-800-RECOTON para obtener información detallada sobre lo que debe hacer y los cargos por el servicio.
▲
▲
To Next Page
Need help?
General
