Why does my Jimmy Vacuum Cleaner have no suction?
If you notice the suction power of your Jimmy Vacuum Cleaner decreasing, there are a few potential causes: * The dust cup might be full, in which case you should empty it. * The filter could be blocked, so try cleaning or replacing it. * The floorhead air path may be obstructed; clean it to restore suction.
How to fix a Jimmy Vacuum Cleaner when the motor does not work?
If the motor of your Jimmy Vacuum Cleaner isn't working, it could be due to a couple of reasons. First, the battery might be completely drained, so try charging the vacuum cleaner. Alternatively, the metal tube, floorhead, battery pack, and vacuum cleaner might not be assembled correctly. Ensure all accessories are properly connected.
Why does my Jimmy H10 Pro Vacuum Cleaner have a short working time after charging?
If your Jimmy Vacuum Cleaner isn't holding a charge for very long, there are a couple of things to consider. First, ensure the machine is fully charged according to the instruction manual. If the battery is old, it may be aging, and you may need to purchase new batteries from a local distributor.
What to do if the dust content indicator is always red on Jimmy Vacuum Cleaner?
If the dust content indicator on your Jimmy Vacuum Cleaner is always red, it's likely that the dust sensor is covered by dust. To resolve this, clean the dust on the dust sensor, which is located in the suction inlet of the handheld vacuum cleaner.
What causes defect of F1 to F8 on Jimmy Vacuum Cleaner?
If you are experiencing a defect of F1 to F8 on your Jimmy Vacuum Cleaner, there could be several potential causes: * A broken battery pack nickel strip. Solution: Replace or repair the battery pack. * A charger defect. Solution: Replace the charger. * A vacuum motor short circuit, 1st or 2nd over current protection. Solution: Replace the vacuum motor. * A battery cell defect. Solution: Replace or repair the battery pack. * A PCB defect or PCB leadwire loose. Solution: Replace PCB or PCB leadwire. * A battery pack PCB defect. Solution: Replace or repair the battery pack.
Why has my Jimmy H10 Pro suction dropped?
If the suction of your Jimmy Vacuum Cleaner has dropped, it could be due to several reasons. First, check if the dust cup is full and needs cleaning. Another possible cause is a blocked filter, which requires cleaning or replacement. Lastly, inspect the floorhead air path for any blockages and clean it thoroughly.
How to fix dust content indicator that is always red on Jimmy H10 Pro Vacuum Cleaner?
If the dust content indicator on your Jimmy Vacuum Cleaner is always red, it's likely that the dust sensor is covered by dust. To resolve this, clean the dust on the dust sensor, which is located in the suction inlet of the handheld vacuum cleaner.
What to do if Jimmy H10 Pro Vacuum Cleaner motor does not work?
If your Jimmy Vacuum Cleaner's motor isn't working, there are a couple of things to check. First, make sure the battery has enough power by charging the vacuum cleaner. Also, verify that the metal tube, floorhead, battery pack, and vacuum cleaner are all assembled correctly.
Why Jimmy Vacuum Cleaner has short working time after charging?
If your Jimmy Vacuum Cleaner isn't holding a charge for very long, there could be a couple of reasons. First, ensure that the machine is fully charged by following the instruction manual. If the battery is old, you may need to purchase new batteries from a local distributor.
What does error F3 mean on Jimmy H10 Pro?
If your Jimmy Vacuum Cleaner displays error F3, it indicates a vacuum motor short circuit. The suggested solution is to replace the vacuum motor.
General| Type | Cordless Stick Vacuum |
|---|---|
| Dust Capacity | 0.6 liters |
| Charging Time | 4-5 hours |
| Dust Collection Type | Bagless |
| Cord Type | Cordless |
| Filtration System | HEPA filter |
Instructions for connecting the electric floor head to the flexible metal tube.
Instructions for charging the vacuum cleaner and its battery pack.
To Next Page
