John Lewis Charlotte Bed 80371707

Need help?

Do you have a question about the John Lewis Charlotte Bed 80371707 and is the answer not in the manual?

Summary

PRE-ASSEMBLY PREPARATION

Lifting and Handling Safety

Important safety advice regarding the weight, lifting, and small parts of the product.

Step-by-Step Assembly Instructions

Step One

Hook side rails to headboard and footboard loosely.

Step Two

Insert and secure the centre rail, then tighten all previous fixings.

Assembly Steps Continued

Step Three

Attach legs to metal plates using washers and nuts.

Step Four

Attach legs to headboard and footboard using bolts and screws.

Final Assembly Steps

Step Five

Insert slats with appropriate centre and side caps.

Care and Maintenance

Cleaning Instructions

Clean with a soft damp cloth and dry immediately. Avoid excessive moisture and detergents.

Safety Instructions

Guidelines for safe handling, assembly, and general product usage.

The Charlotte Bed is a double bed designed for safe and satisfactory operation, requiring assembly before use. This manual provides step-by-step instructions for assembly, along with a checklist of fittings and parts, care and maintenance guidelines, and safety instructions.

Function Description:

The Charlotte Bed serves as a sleeping platform, designed to be assembled from various components including a headboard, footboard, side rails, slats, and a centre rail, supported by legs. Its primary function is to provide a stable and comfortable base for a mattress, accommodating two individuals as a double bed. The design incorporates both normal and wide slats, arranged in specific zones to ensure proper support and stability. The assembly process involves securing the main structural components with bolts and nuts, followed by attaching the support legs and finally installing the slats with their respective caps.

Important Technical Specifications:

Bed Type: Double Bed
Assembly Time: Approximately 40 minutes
Required Personnel for Assembly: 2 people
Compliance: BS EN 1725:1998
Fittings:
- M4 Allen Key (x1)
- M5 Allen Key (x1)
- Centre Caps (x7)
- Side Caps (x14)
- Wide Centre Caps (x8)
- Wide Side Caps (x16)
- M6 X 25mm Bolt (x10)
- M8 Spring Washer (x4)
- M8 Nut (x4)
- Screw 3.5 X 30mm (x4)
- M13 Spanner (x1)
Parts:
- Headboard (x1)
- Footboard (x1)
- Side Rails (x2)
- Slats (x14)
- Wide Slats (x16)
- Centre Rail (x1)
- Legs (x4)
- Metal Plates (x4)
Fasteners: The bed utilizes M6 x 25mm bolts for securing the centre rail and legs, M8 nuts and spring washers for attaching legs to metal plates, and M5 Allen key for tightening side rail fixings. Screws 3.5 x 30mm are used for additional leg attachment.
Slat System: The bed features a combination of normal and wide slats, with specific caps (Centre Caps, Side Caps, Wide Centre Caps, Wide Side Caps) for secure installation. The slat arrangement is zoned (Zone 1: 2 Lines Normal slats, Zone 2: 2 Lines Wide slats, Zone 3: 2 Lines Normal slats, Zone 4: 4 Lines Wide slats, Zone 5: 2 Lines Normal slats, Zone 6: 2 Lines Wide slats, Zone 7: 1 Line Normal slat).

Usage Features:

Assembly Process: The assembly is divided into six steps.
- Step One: Involves hooking side rails onto the headboard and footboard and hand-tightening them loosely. This loose fitting is crucial to allow for the centre rail to be fitted in the subsequent step.
- Step Two: Focuses on inserting the centre rail into the brackets of the headboard and footboard, securing it with M6 x 25mm bolts and an M4 Allen key. After this, the side rail bolts from Step One are fully tightened with an M5 Allen key.
- Step Three: Details the assembly of the legs. Metal plates are attached to the legs using M8 spring washers and M8 nuts, tightened with an M13 spanner. This step is repeated four times for all legs.
- Step Four: Involves attaching the assembled legs to the headboard and footboard using M6 x 25mm bolts and 3.5 x 30mm screws, tightened with an M4 Allen key. This step is performed twice for the headboard and twice for the footboard.
- Step Five: Describes the installation of the slats. Slats (both normal and wide) are inserted into centre caps and then into side caps. Wide slats must be used with wide centre and wide side caps. The process is repeated for all slats, following a specific zoned arrangement for optimal support.
- Step Six: The final step, indicating that the bed is ready for use once all previous steps are completed.
Safety Precautions:
- The product is heavy and requires care when lifting to avoid personal injury or damage.
- Small items in the fittings pack should be kept away from young children.
- Never drag the furniture; always lift it when moving.
- Periodically check and re-tighten all fixings to ensure they have not come loose.
- Careless handling during moving can cause damage or injury.
- Assembly should be carried out by a competent adult.
- Children should be kept away during assembly due to the risk of injury.
- Do not use the item if any components are missing or damaged.
- Take care when moving heavy objects to avoid personal injury or damage.

Maintenance Features:

Cleaning: The bed should be cleaned using a soft, damp cloth and dried immediately. Avoid using very wet cloths or allowing liquid contact for prolonged periods, as this can permanently damage the surface. Do not use detergents or rub the surface, as this can cause permanent damage.
Protection: Protect the bed from direct sunlight, which can accelerate natural discolouration.
Tightening Screws: Screws holding the bed frame together should be tightened regularly to maintain stability and safety.
Information Retention: The information leaflet should be retained for future reference, particularly for care and maintenance guidelines or if additional support is needed.
Support: A helpline (01244 689949) and email (mail@fwgroup-uk.com) are provided for product support, spare parts, additional information, or any issues.