Jula 242-115 - User Manual

Need help?

Do you have a question about the Jula 242-115 and is the answer not in the manual?

Summary

SAFETY INSTRUCTIONS

Special instructions for laser

Warning about laser radiation, not looking into the beam, and not pointing it at reflective surfaces.

Intended use

Specifies the machine's purpose for cutting wood/plastic and prohibits other uses like cutting firewood.

TECHNICAL DATA

DESCRIPTION

ILLUSTRATIONS

OPERATION

BEFORE FIRST USE

General setup and preparation before the first use of the machine.

Fit the saw blade (fig. 1-2, 5-8)

Step-by-step guide for attaching the saw blade, adjusting the turntable, and managing the machine head.

Anchor the saw to the worktop (fig. 1)

Instructions for securely fastening the saw to a workbench or stable surface using bolts.

Fine adjustment of the stop when cross cutting 90° (fig. 1, 9-10)

Details on setting the stop accurately for 90° crosscuts, including indicator adjustments.

Fine adjustment of the stop when sawing 45° mitres (fig. 1, 11-13)

Instructions for precise adjustment of the stop for 45° mitre cuts, including indicator adjustments.

Cross cutting 90° and 0° turntable (fig. 1-2, 14)

Performing 90° cross cuts with the turntable at 0°, covering different saw widths and operation.

Cross cutting 90° and turntable 0°-45° (fig. 1-2, 15)

Performing 90° cross cuts with the turntable angled from 0° to 45° left or right.

Mitre sawing 0°-45° and turntable 0° (fig. 1-2, 16)

Making mitre cuts from 0° to 45° with the turntable set at 0°.

Mitre sawing 0°-45° and turntable 0°-45° (fig. 1-3, 17)

Performing mitre cuts at various angles (0-45°) with the turntable also set at various angles (0-45°).

Limiting the cutting depth (fig. 18)

Adjusting the screw to set maximum cutting depth and performing a test cut.

Dust bag (fig. 1-3)

Information on the dust bag, its emptying, and connecting dust extraction.

Changing the saw blade (fig. 1, 19-23)

Step-by-step instructions for safely replacing the saw blade, including precautions.

Using the laser (fig. 1, 24)

How to turn the laser on/off and adjust its position for accurate cutting lines.

MAINTENANCE AND SERVICE

Carbon brushes

Advice on checking carbon brushes for arcing and warning about replacement by authorized personnel.

Replacing the power cord

Instructions for replacing a damaged power cord by qualified personnel.

TRANSPORT

Summary

SAFETY INSTRUCTIONS

Special instructions for laser

Warning about laser radiation, not looking into the beam, and not pointing it at reflective surfaces.

Intended use

Specifies the machine's purpose for cutting wood/plastic and prohibits other uses like cutting firewood.

TECHNICAL DATA

DESCRIPTION

ILLUSTRATIONS

OPERATION

BEFORE FIRST USE

General setup and preparation before the first use of the machine.

Fit the saw blade (fig. 1-2, 5-8)

Step-by-step guide for attaching the saw blade, adjusting the turntable, and managing the machine head.

Anchor the saw to the worktop (fig. 1)

Instructions for securely fastening the saw to a workbench or stable surface using bolts.

Fine adjustment of the stop when cross cutting 90° (fig. 1, 9-10)

Details on setting the stop accurately for 90° crosscuts, including indicator adjustments.

Fine adjustment of the stop when sawing 45° mitres (fig. 1, 11-13)

Instructions for precise adjustment of the stop for 45° mitre cuts, including indicator adjustments.

Cross cutting 90° and 0° turntable (fig. 1-2, 14)

Performing 90° cross cuts with the turntable at 0°, covering different saw widths and operation.

Cross cutting 90° and turntable 0°-45° (fig. 1-2, 15)

Performing 90° cross cuts with the turntable angled from 0° to 45° left or right.

Mitre sawing 0°-45° and turntable 0° (fig. 1-2, 16)

Making mitre cuts from 0° to 45° with the turntable set at 0°.

Mitre sawing 0°-45° and turntable 0°-45° (fig. 1-3, 17)

Performing mitre cuts at various angles (0-45°) with the turntable also set at various angles (0-45°).

Limiting the cutting depth (fig. 18)

Adjusting the screw to set maximum cutting depth and performing a test cut.

Dust bag (fig. 1-3)

Information on the dust bag, its emptying, and connecting dust extraction.

Changing the saw blade (fig. 1, 19-23)

Step-by-step instructions for safely replacing the saw blade, including precautions.

Using the laser (fig. 1, 24)

How to turn the laser on/off and adjust its position for accurate cutting lines.

MAINTENANCE AND SERVICE

Carbon brushes

Advice on checking carbon brushes for arcing and warning about replacement by authorized personnel.

Replacing the power cord

Instructions for replacing a damaged power cord by qualified personnel.

TRANSPORT

Jula 242-115 Specifications

General

Type	Circular saw
Blade diameter	190 mm
Bore diameter	20 mm
Power	1200 W
No-load speed	5000 rpm
Max cutting depth at 90°	65 mm
Weight	3.6 kg

Related product manuals

Jula 242-160

36 pages

Jula Meec Tools 020-192

84 pages

Jula 242-115 - User Manual

Table of Contents

Summary

SAFETY INSTRUCTIONS

Special instructions for laser

Intended use

TECHNICAL DATA

DESCRIPTION

ILLUSTRATIONS

OPERATION

BEFORE FIRST USE

Fit the saw blade (fig. 1-2, 5-8)

Anchor the saw to the worktop (fig. 1)

Fine adjustment of the stop when cross cutting 90° (fig. 1, 9-10)

Fine adjustment of the stop when sawing 45° mitres (fig. 1, 11-13)

Cross cutting 90° and 0° turntable (fig. 1-2, 14)

Cross cutting 90° and turntable 0°-45° (fig. 1-2, 15)

Mitre sawing 0°-45° and turntable 0° (fig. 1-2, 16)

Mitre sawing 0°-45° and turntable 0°-45° (fig. 1-3, 17)

Limiting the cutting depth (fig. 18)

Dust bag (fig. 1-3)

Changing the saw blade (fig. 1, 19-23)

Using the laser (fig. 1, 24)

MAINTENANCE AND SERVICE

Carbon brushes

Replacing the power cord

TRANSPORT

Summary

SAFETY INSTRUCTIONS

Special instructions for laser

Intended use

TECHNICAL DATA

DESCRIPTION

ILLUSTRATIONS

OPERATION

BEFORE FIRST USE

Fit the saw blade (fig. 1-2, 5-8)

Anchor the saw to the worktop (fig. 1)

Fine adjustment of the stop when cross cutting 90° (fig. 1, 9-10)

Fine adjustment of the stop when sawing 45° mitres (fig. 1, 11-13)

Cross cutting 90° and 0° turntable (fig. 1-2, 14)

Cross cutting 90° and turntable 0°-45° (fig. 1-2, 15)

Mitre sawing 0°-45° and turntable 0° (fig. 1-2, 16)

Mitre sawing 0°-45° and turntable 0°-45° (fig. 1-3, 17)

Limiting the cutting depth (fig. 18)

Dust bag (fig. 1-3)

Changing the saw blade (fig. 1, 19-23)

Using the laser (fig. 1, 24)

MAINTENANCE AND SERVICE

Carbon brushes

Replacing the power cord

TRANSPORT

Jula 242-115 Specifications

Related product manuals