JVC DX-T99A User Manual

1-64 (No.MB531)
4.3.4 DVD check modes
Press MENU key again to enter CHECK MODE. (TEST MODE, MODE STATE, CHECK MODE)
LCD display
Press "1" key on remote control to start playback.
LCD display
Press "2" key on remote control to perform SEARCH TNO+1
LCD display
Press "3" key on remote control to perform SEARCH TNO+1
LCD display
Press "4" key on remote control to light up CD_LD and display laser current.
LCD display
Press "5" key on remote control to light up DVD_LD and display laser current.
LCD display
Press "6" key on remote control to enter DVD x 2 jitter measurement mode
LCD display
Press "9" key on remote control to perform SEARCH DVD_SL DESIGNATED POSITION and JITTER MEASUREMENT
LCD display
Press "+10" key to INITIALIZE EEPROM (MECHA)
LCD display
CHECK
CHECK
PL A AYB KC
CDL LDRS
ccc jcj jj
WO B EBL
(2 seconds)
(2 seconds)
(Static)
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj
ccc jcj jj
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj
DVDL LDRS
(2 seconds)
(Static)
ccc jcj jj
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj
JI TX1
(2 seconds)
(Static)
ccc jcj jj
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj
DLVD S
INIT
Press PLAY key on remote control to start PLAYING and obtain LASER CURRENT and JITTER value.
LCD display
Press STOP key on remote control to stop JITTER measurement.
LCD display
(2 seconds)
(Static)
ccc jcj jj
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj
LTSR J I
(2 seconds)
(Static)
ccc jcj jj
(Static)
CH KEC
During CHECK mode, at any time press MENU key to exit CHECK mode and return to starting screen of DVD TEST MODE.
* During TEST mode, at press POWER key send POWER OFF command to MECHA-CON and if power off permit flag is 1,
display "POFF OK"
PO KFFO
cccc: Byte 0 = 0x00, Byte 7 = 0x00, Byte 3,4 -> DISPLAY
j j j j: Byte 0 = 0x00, Byte 7 = 0x00, Byte 5,6 -> DISPLAY
Status: 00 (NORMAL) XX XX cc cc jj jj

JVC DX-T99A Specifications

General

Brand	JVC
Model	DX-T99A
Category	Stereo System
Language	English