JVC GX-N7E User Manual

H
i
|
Position
@:
Set
IRIS
CONTROL
switch
®
to
this
posi-
HOW
TO
OPERATE
THE
VIDEO
CAMERA
[1] HOW TO SUPPLY POWER
= When connected to JVC compact VTR HR-C3.
In this case, it is possible to switch the VTR on from the
@ When connected to a VTR with a camera connection
terminal. (See 11] WHEN THE VTR HAS A CAMERA
CONNECTION TERMINAL in “HOW TO CONNECT camera,
TO A VTR” section on page 6E.)
Power
is
supplied
to
the
camera
when
the
VTR
is
@
Push
POWER
button
@
to
switch
the
VIR
switched on. on.
@
When
connected
to
a
VTR
with
no
camera
connection
0)
®
Push
it
again
to
switch
the
VTR
off.
terminal.
(See
page
6E.)
Power
is
supplied
to
the
camera
when
the
VTR
is switched on.
Power
is
supplied
to
the
camera
when
the
AC
adaptor
is
switched on.
Notes:
Note:
Switching
the
VTR
on
from
the
camera
is
possible
© Power supply to the camera may be different according
only when connected to JVC compact VTR HR-C3.
to the type of VTR connected. Refer to the VTR’s
instruction manua! for details.
©
Be
sure
to
remove
the
lens
cap
@
only
after
supplying
power
to
the
camera,
and
do
not
forget
to
switch
off
the
power
supply
after
replacing
the
cap.
Do
not
aim
the
lens
directly
at
the
sun
or
other
strong
light
sources.
Incorrect
use
could
damage
the
pickup
tube.
HOW
TO
USE
THE
IRIS
CONTROL
SWITCH
For standard shooting, set IRIS CONTROL switch ®
to position @
Position
©:
Set
switch
@
to
this
position
to
select
the
AUTO
IRIS
control
mode.
The
iris
is
auto-
matically
adjusted
according
to
the
brightness
of
the
scene.
tion to select the manual [RIS CONTROL
mode. Then turn IRIS CONTROL knob @®
in either direction (Refer to the following de-
scription of IRIS CONTROL knob @®) to
adjust the iris manually.
Using IRIS CONTROL knob ®
@
side
:
Turn
[RIS
CONTROL
knob
@
in
direction
@
to
make
the
picture
brighter
(by
opening
the
aperture).
Turn ERIS CONTROL knob @® in direction
@ to make the picture darker {by closing the
aperture}.
@ side :
Note:
IRIS
CONTROL
knob
@
operates
only
when
IRIS
sun
imok
switcn
@®
15
set
to
position
1)
R
a BE=
HOW
TO
USE
THE
BLC
(
BACKLIGHT
COMPENSATION)
SWITCH
|
For
standard
shooting,
set
BLC
(backlight
compensation)
switch
@
10
position
“O’’,
|
Position + : Set BLC switch @ to the “+” position to allow the iris to open by approxi-
mately
1/2
an
f-stop
above
the
standard
AUTO
IRIS
setting.
Use
this
func-
tion
when
the
subject
is
too
dark
and
the
background
is
too
bright.
+
t
0
PositionO
:
Set
BLC
switch
@
to
the
“Q’
position
to
release
the
BLC
function
or
restore the standard AUTO IRIS CONTROL function.
Note:
BLC
switch
@
can
operate,
only
when
IRIS
CONTROL
switch
@®
is
set
to
posi-
tion.
HOW
TO
USE
THE
FOCUS
SWITCH
For standard shooting, set FOCUS switch @ to position Q.
Lower
position
@
:
Set
FOCUS
switch
@
to
this
position
to
focus
automatically.
Manual
position@
:
Set
FOCUS
switch
@
to
this
position
to
focus
manually,
and
then
turn
focus
ring
@
to
bring
the
subject
into
focus.
+»...
._.
CA}
Upper
position
@:
@
Hold
FOCUS
switch
@
pushed
up
in
this
position
for
POWER
ry
A
ry
FOCUSING
[instant
auto
focusing).
()
*@
Release
switch
@
to
return
to
MANUAL
FOCUSING.
After
A}
releasing
switch
@
it
will
return
automatically
to
its
manual
position
@
.
The
GX-N7E
has
a
semi-TTL
(through-the-lens)
active
infrared
auto
focus
system
designed
to
focus
on
the
subject
automatically.
This
camera
transmits
infrared
rays
from
just
above
the
center
of
the
fens.
These
rays
hit
the
subject
and
are
reflected
to
the
infrared
receiver
on
the
front
of
the
camera
which
in
turn
calculates
the
optimum
focus
automatically.
Infrared transmitter
Infrared receiver
~9E —

JVC GX-N7E Specifications

General

Brand	JVC
Model	GX-N7E
Category	Camcorder
Language	English