JVC HR-S5200U - Advanced Recording Features; Instant Timer Recording; Hi-Fi Audio and Tape Format; Stereo and SAP Audio Recording

& Recording (cont'd)
REC
Accidental erasure prevention:
& To prevent accidental recording on a recorded cassette, remove
its safety tab. ©
To record on it later, cover the hole with adhesive tape.
EN-26
Instant Timer Recording
To set the VCR to shut-off automatically after recording.
During Recording...
[0] Press the VCR's REC button. The "ITR" indication blinks and
"0:30" appears indicating the recording will.continue for" 30
minutes and then power will switch off.
7.7
Lt kl
{2] Press REC again to extend the record time by 30-minute
increments (up to 9 hours).
™ This function is available only using the REC button on the
VCR.
m After the off-time is set, the display returns to the
previously displayed mode (counter, channel, clock or
remain), :
You can check the time remaining before the VCR shuts off
by pressing REC once; the remaining time is displayed for
5 seconds. (Pressing REC more than once will extend the
record time.)
To display the remaining tape time
Press ENTER. Counter information appears on the screen,
Press DISPLAY until "REMAIN" appears. Approximate
remaining tape time appears on the TV screen and VCR
display panel.
@ If recording is in progress, the remaining time display on
the VCR changes back to the "REC" mode display after 5
seconds.
™ Pressing DISPLAY repeatedly changes the displayed
indication (Counter —-~ Channel —> Clock time—- Remain).
{3] Press ENTER again to clear it from the screen.
Hi-Fi Audio Recording Level Control
Your VCR allows manual adjustment of the Hi-Fi audio
recording level. Although the preset audio recording level is
satisfactory for normal recording, if the sound you are going to
record is too loud or too low, adjust the audio recording level
while referring to the VCR's audio level meters.
[i] Press MENU, SET, and Fi FI REC LEVEL CONTROL
SELECT .as many times as PRESET
necessary to access the HI-FI MANUAL
REC LEVEL CONTROL PRESS
re
Phe
PRESS {SET +/+) FOR CHOICE
PRESS (MENU) TO END
screen. (C7 p.7)
{2] Press SET to choose "MANUAL".
[3] Press FF or REW to adjust the
audio recording level.
@ To move the on-screen's audio levels by one division of the
scale, press. FF or REW briefly for 5 times in succession.
To move the audio levels faster, keep FF or REW presssed.
Adjust the recording level so that the audio level meters
reach from 0dB to 4dB at the maximum sound volume.
. [4] Press MENU as many’times as necessary to exit.
NOTE:
@ Noise will increase if the recording level is too low, while
distortion will increase if the level is too high.
S-VHS indicator
S-VHS (Super VHS) and VHS
Your VCR can record in either S-VHS or VHS.
@ To record in S-VHS, insert.a cassette marked "S-VHS". The S-
VHS indicator will light and the S-VHS recording mode is
automatically selected,
™ To.record in VHS, insert a cassette marked "VHS". The VHS
recording mode is automatically selected.
™ You can also record in VHS on S-VHS cassettés. To do this,
after inserting an S-VHS cassette, press the S-VHS button. The,
S-VHS indicator will go out.
Stereo and SAP
(Second Audio Program)
Your VCR. is equipped with an MTS decoder for reception of
Multichannel TV Sound broadcasts.
@ When a stereo program is being received, the ST indicator lights.
When an SAP program (such as a bilingual broadcast) is being
received, the SAP indicator lights. i
™ When a stereo program is accompanied by SAP audio, both
indicators light.
To. record stereo programs
audio track: No special operation is required: Simply follow the
basic recording procedure.
@'To listen to the stereo soundtrack while recording, set the on-
screen AUDIO MONITOR to "HI-FI". #7 p, 20.
To record SAP programs
[1] Press MENU, SET, and
SELECT as many times as
necessary to access the 2ND
AUDIO screen. (CF p. 7).
(2] Press SET to choose "ON".
[3} Press MENU as many times as
necessary to exit.
Then follow the basic recording procedure.
m If an SAP program is received, the SAP audio wil! be recorded
-on both the Hi-Fi and the normal-audio tracks. The main audio
program will not be recorded,
® If a regular program (non-SAP) is received, the main audio will
2ND AUDIO
ON
. OFF
PRESS (SET iO YSE CHOICE
PRESS (MENU) TO END
Stereo;programs are automatically recorded in stereo on the Hi-Fi
be recorded on both the Hi-Fi and the normal audio tracks.
EN-27