JVC UX-A4 - Analytic Drawing (2) Parts List; Disassembly of Front Panel Assy

B Analytic Drawing (2) Parts List
peer
A
B
BLOCK NO. MeMM [TT
REMARKS SUFFIX
REF .32-34
REF .28,-29
E-G-GI-EN
PARTS NO.
ZCUXDA4K-CLB
ZCUXDA4K-CH
VXP3602-001
SBSF2608Z
VYH3787-001
VYSA1R4-059
VYH7817-001
VXQ4118-001
SDSF2608Z
VK24323-002
VKW3002-274
VYH7347-001
VKZ4341-001
VKW4938-001
VJT2263-003
VKY4180-001
VYH5601-001
VKW5110-001
VJT2330-001
E406971-221
VJT4209-001
VKL7293-001
SBSF3010Z
VKW5069-001
SBSF3008Z
SBST3006Z
VJC3237-003
VJF4003-003
SDST3004Z
VMA4603-001
SBST30082Z
VMA4604-002
QHX5080-001
VYH3658-002
QHS3876-162BS
QHS3876-162
VYH7698-002
SBST3008Z
VMH4046-002
$$$T30082
SDST30122
PARTS NAME
CASSETTE LID
CASSETTE HOLDER
BUTTON
SCREW
HOLDER
SPACER
EJECT LEVER
EJECT KNOB
SCREW
SCREW
TENSION SPRING
EJECT ARM
SPECIAL SCREW
TORTION SPRING
CASS DOOR
CASSETTE SPRING
GEAR
COOR SPRING
DOOR COVER
JVC MARK
DOOR LENS
EJECT SAFTYCR)
SCREW
TORSION SPRING
SCREW
SCREW
BOTTOM COVER
FOOT
SCREW
SHIELD PLATE
SCREW
BARRIER
WIRE CLAMP
TRANS BRACKET
CORD STOPPER
CORD STOPPER
JACK HOLDER
SCREW
HEAT SINK
SCREW
SCREW
FRONT+SW BOARD
HOLDER
EJECT
EJECT
EJECT SAFTEY
EJECT SAFTEY
F.PANEL+MECHA.
HOLDER+MECHA.
SHIELD+T.BKT
J.HOLDER+FUSE P
FOR FUSE PCB
POWER CORD
POWER CORD
J.HODER+TRANS B
HEAT SINK+T.BKT
SBST40062 SCREW POWER TRANS
VYH7696-001 JACK STOPPER
SBSF30082 SCREW JACK STOPPER
PRP ER NINP UP BP PWR PIP UN BNI P PP BIP PP RP NIP PP RP BI RP PR RIP WR Re
VYH7708-002
SDST26082Z
Ic HOLDER
SCREW
Ic+IC BKT
VMZ0087-0012 FUSE CLIP
VND4003-034 FUSE LABEL FOR F951
VND4003-050 FUSE LABEL FOR F952
eee ee
VND4003-050 FUSE LABEL FOR F953
SBST30062 SCREW TRANS BKT 4
$8S$T30062 SCREW HOLDER+F.PANEL 2
VJG1238-001
FRONT
PANEL
(CD)
1
QMF51E2-R40J1 FUSE F951 1
PARTS NAME
FUSE
FUSE
POWER TRANS
POWER TRANS
PARTS NO.
VTP66T2-12DBS
VTP66J2~-12D
Operation key switch P.C.board
Headphone jack P.C.board
Cassette mechanism
Pre — amplifier
Bias OSC P.C.board
Recording amplifier P.C.board
Fig. 7-3
1.
UX-A4 B/E/G/GI/EN
BLOCK NO. MeMM [TT]
REMARKS SUFFIX CLR
E-G-GI-EN
F9S2 1
F9S4 1
1) 8
1
Hi Disassembly of Front Panel Ass’y
Cassette Mechansim (Fig. 7-2, 3)
After raising (floading) the recording amplifier P.C. board
upward, dismount the connectors CNAOQ3 and CNAO04
on the P.C. board respectively from the connectors
CNAO1 and CNAO2 on the pre-amplifier bias OSC P.C.
board.
. Remove the four screws (G8) x 2 and 9) xX 2) retain-
ing the cassette mechansim from the front panel ass’y.
. Pull out the flexible head wire from the connector CNA06
on the pre-amplifier bias OSC P.C. board.
. After drawing the pre-amplifier bias OSC P.C. board
toward the front side, dismount the connector CN805
on the P.C. board from the connector CN806 on the
operation switch P.C. board.
Headphone Jack P.C. Board (Fig. 7-2, 3)
The headphone jack P.C. board can be dismounted by
drawing it out toward the front side from inside the front
panel ass’y.
(No. 1 890) 27