Kalerm KLM1604 - User Manual

Questions and Answers

S
Shannon BruceAug 20, 2025
What to do if my Kalerm Coffee Maker displays 'FILL WATER TANK'?
- T
  Tiffany GrahamAug 20, 2025
  If the display of your Kalerm Coffee Maker shows 'FILL WATER TANK', the following could be the reasons: * The water tank is empty; simply fill it. * The water tank is not correctly installed; ensure it is properly placed. * The ball inside the water tank is stuck; clean the tank and gently knock near the ball to free it. * The ball has fallen off or is damaged; replace the water tank group (item: 8810101020). * The reed sensor is damaged; replace it (item: 73000095). * The connector is damaged; connect or repair the power switch connector. * The PCBA is damaged; replace or repair the PCBA (item: 78000056).
J
Jaclyn CannonAug 23, 2025
Why is the coffee temperature too low on my Kalerm KLM1604 Coffee Maker?
- H
  hgarciaAug 23, 2025
  If the coffee temperature from your Kalerm Coffee Maker is too low (below 70°C), consider the following: * The cup's temperature might be too low; preheat the coffee cup or increase the ambient temperature. * The water temperature may be too low; use pure water around 25°C. * The machine might be cold due to low temperature or long standby time; the temperature should meet the standard by the third cup. * The coffee machine may need descaling, as deposits can decrease the thermoblock's efficiency; perform a descaling process.
K
Kara MontgomeryAug 26, 2025
What to do if the drip tray cannot be installed in my Kalerm Coffee Maker?
- M
  masseybrittanyAug 26, 2025
  If the drip tray of your Kalerm Coffee Maker cannot be installed in place, check these potential causes: * The data interface cover on the front panel might be shedding; reassemble the data interface cover, ensuring it's fitted to the front panel group (item: 73000202). * There may be excessive coffee powder on the base; remove the drip tray and clean any coffee powder from the base. * The brew unit may not have reset; try the following steps: 1. Remove the coffee ground container. 2. Insert the drip tray. 3. Press ON/OFF. 4. After the machine resets and the screen shows "HEATING", remove the drip tray. 5. Place the coffee ground container on the drip tray and re-insert them. * The drip tray group components could be damaged; consider replacing the components.
S
Sarah RogersAug 28, 2025
Why is my Kalerm KLM1604 leaking water when filling or removing the water tank?
- M
  Mary PriceAug 28, 2025
  If you notice water leaking from the bottom of your Kalerm Coffee Maker when removing or filling the water tank: * The valve body might be stuck and unable to reset; try moving the valve body to reset it. * Some components could be damaged; consider replacing them.
B
Brittany LongAug 30, 2025
Why is the coffee temperature too high on my Kalerm KLM1604 Coffee Maker?
- A
  arogersAug 30, 2025
  If the coffee from your Kalerm Coffee Maker is too hot (over 89°C): * The NTC may be loose or unfixed; ensure it is properly secured. * The NTC thermistor might be damaged; replace it with item 73000221. * There could be damage to the program or PCBA; consider replacing or repairing the PCBA (item: 78000056).
H
Helen HudsonSep 2, 2025
How to fix a powder container cover that won't close tightly on my Kalerm KLM1604 Coffee Maker?
- M
  mmaysSep 2, 2025
  If the powder container cover on your Kalerm Coffee Maker won't close tightly: * There might be coffee powder left below the cover; clean the coffee powder. * The powder container cover may be deformed; replace it with powder container cover 79000123.
T
thomas36Sep 4, 2025
Why does my Kalerm KLM1604 Coffee Maker drip water during cleaning?
- A
  Adam WilliamsSep 4, 2025
  If a small amount of water drips from the coffee outlet during the cleaning cycle of your Kalerm Coffee Maker: * The brew unit filter screen might be clogged; try running the CLEAN program from the menu. * There could be damage or a leak in the internal pipe connector; repair the damaged pipe or connector. * The drainage valve group may be damaged; consider replacing the drainage valve group.
D
Daniel RobertsonSep 7, 2025
Why no coffee comes out from Kalerm Coffee Maker?
- D
  Diana VillarrealSep 7, 2025
  If no coffee is dispensing from the coffee outlet of your Kalerm Coffee Maker, the drainage valve group may be damaged, preventing water from reaching the brew unit and causing it to drip directly into the drip tray. Consider replacing the drainage valve group.
B
Brett SmithSep 9, 2025
Why is the coffee volume too little on my Kalerm Coffee Maker?
- Q
  qhernandezSep 9, 2025
  If your Kalerm Coffee Maker is dispensing too little coffee (less than 25ml for an Espresso), it might need descaling. Deposits inside the machine's pipes could be causing a blockage. Perform a descaling process.
S
sandersnicoleSep 12, 2025
How to fix a damaged power cord on a Kalerm KLM1604?
- J
  julieryanSep 12, 2025
  If the power cord of your Kalerm Coffee Maker is damaged, replace it.

Summary

Safety Instructions

Precautions

Key safety measures to prevent harm during operation and handling.

Warnings

Prohibitions

Actions strictly forbidden to avoid damage, hazards, or injury.

Instructions for First-Time Use

Power Connection

Proper placement and electrical connection of the coffee machine.

Fill Water Tank

Guidelines for filling the water tank with appropriate water for taste.

Fill Beans

Instructions on what type of coffee beans to use and not to use.

Grinding Wheel

How to adjust the coffee bean grind fineness for optimal results.

Power On

Steps and procedures for turning the coffee machine on and initial self-testing.

Power Off

Making Beverages

Making Coffee

Step-by-step guide to brewing coffee using the machine's icons.

Single Time Setting of Coffee Parameters

Making Coffee with Coffee Powder

Making Double Cups of Coffee

How to Use Milk Frother

Guide to creating milk foam and hot milk using the machine's frother.

Cleaning and Maintenance

Rinsing the Coffee Machine

Cleaning the Brewing Unit

Descaling the Coffee Machine

Process for removing mineral buildup (limescale) from the machine.

Rinse Milk Unit

Cleaning the Coffee Grounds Container and the Drip Tray

Cleaning the Water Tank

Cleaning the Bean Container

Cleaning the Coffee Machine

Failures Handling

Kalerm KLM1604 Specifications

General

Type	Automatic Coffee Machine
Water Tank Capacity	1.8 L
Bean Container Capacity	250 g
Pump Pressure	19 bar
Adjustable Coffee Strength	Yes
Adjustable Water Volume	Yes