Kampmann Katherm HK 290 Assembly And Installation Instructions

Name: Kampmann Katherm HK 290
Brand: Kampmann
Rating: 5 (1 reviews)

84 pages

To Next Page

Katherm HK

Ready-to-install trench heaters for heating or

cooling with EC tangential fan

Assembly and installation instructions

Keep these instructions in a safe place for future use!

I517/07/19 EN | SAP No. 1237680

Default Chapter2
- Table of Contents2
1 Intended Use4
- Description4
- Limits of Operation and Use5
2 Safety Information6
3 Designs/Scope of Delivery6
4 Alignment and Positioning7
- Alignment Using Height-Adjustment Feet and Raised Floor Brackets7
- Positioning and Fixing at the Installation Site7
5 Water Connections8
6 Screed Works8
7 Water Connection / Pipe Openings9
8 Katherm HK Optionally with Supply Air Function16
- Katherm HK with Supply Air Modules16
- Katherm HK - Supply Air Ducts ZL18
9 Condensation Drainage20
- General Information20
- Condensation Drainage with a Natural Gradient21
- Condensation Drainage Using the Condensation Pump Kit24
10 Number of Height-Adjustment Feet and Raised Floor Feet27
11 Maintenance28
- Information / Maintenance / Maintenance Intervals28
- Cleaning the Condensation Tray29
12 Consumption Figures30
13 Electrical Wiring31
- Overview of Controls32
- Electromechanical Electrical Model33
- Electromechanical Electrical Model35
14 Katherm HK, Kacontrol Model (*C1)39
- Intended Use39
- Function Keys, Display Elements40
- Operation41
- Activating and Deactivating the Control42
- Temperature Adjustment (Absolute Value)43
- Fan Setting44
- Time Setting45
- Timer Programs46
- Operating Modes (Mode Key)49
15 Alarm Messages50
- Alarm Messages from Kacontrol PCB, Display on Kacontroller50
- Kacontroller Alarm Messages50
16 Troubleshooting51
- A11 Control Sensor Faulty51
- A12 Motor Protection51
- A13 Room Frost Protection Function51
- A14 Condensation Alarm52
- A15 General Alarm52
- A16 Sensor AI1, AI2 or AI3 Faulty52
- A17 Unit Frost Protection Function52
- A18 EEPROM Error53
- A19 Slave Offline in the CAN Network53
- Problem Solution53
17 Kacontroller Installation54
18 Cabling55
- General Information55
- Terminal Resistors in a CAN-Bus System56
- Bus Connections between the Units56
- Kacontroller56
19 Setting Configuration of Unit by Means of DIP Switch57
20 Parameter Settings59
- General59
- Calling up the Service Menu59
- Heating/Cooling Changeover Via Clip-On Sensor in 2-Pipe Systems60
- Setting DIP Switch No. 3, DIP Switch No. 460
- Setting Automatic Heating/Cooling or Day/Eco Changeover Mode60
- Function of Digital Inputs DI1 and DI262
21 Functional Testing of Connected Assemblies67
- External Control Via 068
- Parameter List for Kacontrol PCB69
- Electrical Wiring73
  - Control by On-Site BMS73
  - Master Unit and Slave Units74
22 Declaration of Conformity76

Other manuals for Kampmann Katherm HK 290

Assembly, Installation And Operating Instructions84 pages

Questions and Answers:

Need help?

Do you have a question about the Kampmann Katherm HK 290 and is the answer not in the manual?

Kampmann Katherm HK 290 Specifications

General

Category	Heater
Width	290 mm
Voltage	230 V
Frequency	50 Hz
Heat output (EN 16430)	2.9 kW
Heating capacity	According to selection
Length	According to selection

Related product manuals

Kampmann Katherm HK

84 pages

Kampmann Katherm HK Series

84 pages

Kampmann Katherm HK 290 Assembly And Installation Instructions

Table of Contents

Other manuals for Kampmann Katherm HK 290

Questions and Answers:

Kampmann Katherm HK 290 Specifications

Related product manuals