Kärcher Binford 1750

Questions and Answers

M
marissawardAug 12, 2025
What to do if Kärcher Pressure Washer unit does not reach high pressure?
- W
  Wesley NorrisAug 12, 2025
  If your Kärcher Pressure Washer isn't reaching high pressure, start by checking the diameter of your garden hose; replace it with a 1/2 inch or 5/8 inch garden hose if it's too small. Also, ensure that the water supply isn't restricted by checking the garden hose for kinks, leaks, and blockages. Confirm that there's enough inlet water supply by opening the water source fully. Clean the water inlet filter by removing it and rinsing it in warm water. Finally, make sure the spray wand is set to the high-pressure position.
D
Dustin WilliamsAug 16, 2025
How to fix Kärcher Binford 1750 Pressure Washer motor that won't start?
- T
  tammy91Aug 16, 2025
  If your Kärcher Pressure Washer motor won't start, there are several potential causes. First, ensure the On/Off switch is in the “ON” (I) position. Next, verify that the power cord is properly plugged in. If you're using an extension cord, make sure it's not too long, is of the proper gauge (either a 25 ft. 12/3 gauge cord or a 50 ft. 10/3 gauge cord), and is not damaged. Finally, try a different electrical outlet to rule out inadequate power supply from the original outlet.
J
Jonathan ClementsAug 20, 2025
Why Kärcher Binford 1750 Pressure Washer output pressure varies high and low?
- R
  Rebecca PetersonAug 20, 2025
  The fluctuating output pressure in your Kärcher Pressure Washer can stem from several issues. Ensure you have enough inlet water supply by turning the water on full force and checking the garden hose for any kinks, leaks, or blockages. Another cause might be the pump sucking air; inspect hoses and fittings to ensure they are airtight, then turn off the machine and purge the pump by squeezing the trigger gun until a steady water flow emerges from the nozzle. Also, check if the water inlet filter is clogged and clean it in warm water, or if the discharge nozzle is obstructed, clear it with a fine needle. Lastly, if the gun, hose, or spray wand are calcified, run distilled vinegar through the detergent tank.
A
Alicia PierceAug 23, 2025
Why is there no detergent coming out of my Kärcher Pressure Washer?
- B
  Brent SpencerAug 23, 2025
  If your Kärcher Pressure Washer isn't dispensing detergent, first check if the detergent is too thick and dilute it if necessary. Also, make sure the spray wand tip is in the low-pressure position. Finally, check the discharge nozzle for obstructions and clear any debris with a fine needle.
I
Isaac WilliamsAug 27, 2025
Why is my Kärcher Binford 1750 pump so noisy?
- J
  Jon MilesAug 27, 2025
  A noisy pump in your Kärcher Pressure Washer often indicates that the pump is sucking air. To resolve this, check that all hoses and fittings are airtight. Then, turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle.
L
Larry Torres PhDAug 31, 2025
What to do if Kärcher Pressure Washer spray wand leaks?
- L
  Laura HarrellAug 31, 2025
  If the spray wand on your Kärcher Pressure Washer is leaking, first ensure that the spray wand is properly attached. Insert the spray wand into the trigger gun, carefully press it in against the spring tension, and twist it into the locked position. If the issue persists, it might be due to a broken o-ring or plastic insert.
M
Michael CastroSep 4, 2025
Why is my Kärcher Binford 1750 Pressure Washer leaking water from the pump?
- P
  pamelafrySep 4, 2025
  If your Kärcher Pressure Washer is leaking water from the pump, check that all fittings are tight. The water seals may be damaged or worn.
F
fernandezericSep 7, 2025
Why is my Kärcher Binford 1750 Pressure Washer dripping oil?
- P
  Peter RobersonSep 7, 2025
  If your Kärcher Pressure Washer is dripping oil, it suggests that the oil seals are damaged or worn.