Kärcher K 3.79 M User Manual (English)

Other manuals for Kärcher K 3.79 M

Questions and Answers:

G
Gregg WilsonAug 17, 2025
Why Kärcher Pressure Washer output pressure varies high and low?
- E
  ehaynesAug 17, 2025
  The fluctuating output pressure in your Kärcher Pressure Washer could be due to several reasons. First, ensure you have an adequate water supply by turning the water on full force and checking the garden hose for any kinks, leaks, or blockages. Another cause might be the pump sucking air; inspect hoses and fittings for airtight seals and purge the pump by squeezing the trigger gun until water flows steadily through the nozzle. Also, check the water inlet filter for clogs and rinse it in warm water. The discharge nozzle may also be obstructed, so clear any debris with a fine needle. Finally, run distilled vinegar through the detergent tank to address calcification in the gun, hose, or spray wand.
F
fhaneyAug 20, 2025
How to fix Kärcher K 3.79 M motor that will not start?
- S
  Stephanie HoffmanAug 20, 2025
  If your Kärcher Pressure Washer motor isn't starting, there are a few things to check: * Ensure the On/Off switch is in the “ON” (I) position. * Verify the power cord is securely plugged in. * If using an extension cord, make sure it is not too long, is of the proper gauge (either a 25 ft. 12/3 gauge cord or a 50 ft. 10/3 gauge cord), and is not damaged. Replace if necessary. * Try a different electrical outlet to rule out inadequate power supply.
A
Amber KellyAug 23, 2025
What to do if Kärcher K 3.79 M Pressure Washer unit does not reach high pressure?
- C
  Chad NguyenAug 23, 2025
  If your Kärcher Pressure Washer isn't reaching high pressure, consider the following: * Ensure your garden hose has a sufficient diameter; replace it with a 1/2 inch or 5/8 inch garden hose if needed. * Check the garden hose for any restrictions like kinks, leaks, or blockages. * Make sure the water source is fully open to provide enough inlet water supply. * Inspect the water inlet filter for clogs and rinse it out in warm water. * Confirm that the spray wand is set to the high-pressure position.
B
Bruce KingAug 26, 2025
Why Kärcher K 3.79 M motor will not start?
- M
  Marc MccoyAug 26, 2025
  The Kärcher Pressure Washer motor might not start due to several reasons: the On/Off switch is in the “OFF” (O) position - turn it to the “ON” (I) position; the power cord is not plugged in - plug it in; the electrical outlet does not supply adequate power - try a different outlet; or the circuit breaker is tripped - switch off the pressure washer and wait for the temperature to go down for automatic reset.
W
William AlvarezAug 28, 2025
What to do if Kärcher K 3.79 M has no detergent?
- B
  Brian ClineAug 28, 2025
  If your Kärcher Pressure Washer isn't dispensing detergent, check the following: ensure the detergent suction tube is properly connected to the machine; if the detergent is too thick, dilute it (using Kärcher detergent is recommended); clear any clogs from the filter on the detergent suction tube by running warm water through it; check for damage or obstructions in the detergent suction tube, removing any blockages or replacing the tube if necessary; make sure the spray wand is in the low pressure position; and clear any obstructions from the discharge nozzle.
K
Kelly RamosAug 30, 2025
Why Kärcher Pressure Washer unit does not reach high pressure?
- M
  Michelle BrownAug 30, 2025
  If your Kärcher Pressure Washer isn't reaching high pressure, it could be due to a few reasons: the diameter of the garden hose is too small - replace it with a 5/8 inch garden hose; the water supply is restricted - check the garden hose for kinks, leaks, and blockages; there's not enough inlet water supply - open the water source fully; the water inlet filter is clogged - remove the filter and rinse it in warm water; or the spray wand is on the low pressure position - turn the spray wand to the high pressure position.
D
Debra BallardSep 2, 2025
What to do if Kärcher Pressure Washer garden hose connection leaks?
- S
  Susan KirbySep 2, 2025
  If your Kärcher Pressure Washer's garden hose connection is leaking, check for loose fittings and tighten them. Also, inspect the rubber washer; if it's missing or worn, insert a new one.
C
Charles DelgadoSep 5, 2025
Why is my Kärcher K 3.79 M Pressure Washer pump noisy?
- A
  Angelica SerranoSep 5, 2025
  A noisy pump in your Kärcher Pressure Washer could be due to the pump sucking air. Check that all hoses and fittings are airtight. Turn off the machine and purge the pump by squeezing the trigger gun until a steady flow of water emerges through the nozzle.
E
earlnormanSep 8, 2025
What to do if Kärcher K 3.79 M Pressure Washer spray wand leaks?
- R
  richard49Sep 8, 2025
  If the spray wand on your Kärcher Pressure Washer is leaking, make sure the spray wand is properly attached by inserting it into the trigger gun, carefully pressing it in against the spring tension, and twisting it into the locked position. If the o-ring or plastic insert is broken, call Customer Support.
T
Theresa BarkerSep 12, 2025
Why Kärcher K 3.79 M has water leaks from pump?
- G
  Gina FlemingSep 12, 2025
  If water leaks from the pump of your Kärcher Pressure Washer (up to 10 drops per minute is permissible), check that all fittings are tight. If the water seals are damaged or worn, call Customer Support.