Kärcher NT 40/1 Tact Te User Manual (English)

Other manuals for Kärcher NT 40/1 Tact Te

Instructions40 pages

Service Manual20 pages

Questions and Answers:

R
Richard JohnsonAug 4, 2025
How to fix a Kärcher NT 40/1 Tact Te Vacuum Cleaner when the suction turbine does not run?
- L
  Lindsay ClaytonAug 4, 2025
  If the suction turbine of your Kärcher Vacuum Cleaner doesn't run, here are a few things you can check: * Ensure the appliance is turned on. * If in wet vacuuming mode, empty the container if it's full. * Check the cables, plugs, and mains supply. * Inspect or replace the appliance switch, electrode overflow fuse, socket, microswitch on the socket, suction turbine, or PCB, as needed.
L
lwaltersAug 8, 2025
Why is the automatic filter cleaning not working on my Kärcher NT 40/1 Tact Te?
- A
  Andrew WallaceAug 8, 2025
  If the automatic filter cleaning on your Kärcher Vacuum Cleaner isn't working, ensure the filter cover is properly closed and locked. Check the suction system for leaks and repair them. Also, verify the correct positioning of the flat fold filter. Inspect for leaks between the suction head and the waste container, and make sure the suction hose is connected. If using a suction hose diameter greater than DN 35 on a Te model, ensure the speed regulator is correctly adjusted or set the suction performance to max. Finally, check or replace the Tact filter cleaning system ON/OFF switch or the PCB.
K
Kimberly VincentAug 12, 2025
Why is the suction capacity of my Kärcher NT 40/1 Tact Te Vacuum Cleaner decreasing?
- E
  Elizabeth CastilloAug 13, 2025
  If the suction capacity of your Kärcher Vacuum Cleaner decreases, try the following: * Check for and remove any blockages in the suction nozzle, suction tube, suction hose, or flat pleated filter. * Switch the Tact filter cleaning system on/off or replace it. * Exchange the paper filter bag. * Ensure the filter cover properly locks into place. * Check the suction system for leaks and repair them if necessary. * Clean or replace the membrane filter (special accessory). * Replace the flat pleated filter.
J
Judy PadillaAug 17, 2025
What to do if dust comes out while vacuuming with my Kärcher NT 40/1 Tact Te Vacuum Cleaner?
- J
  jonesjennaAug 17, 2025
  If dust is coming out of your Kärcher Vacuum Cleaner while vacuuming, make sure the flat pleated filter is installed correctly and replace it if necessary.
H
hwallaceAug 21, 2025
What to do if the suction turbine won't switch off on my Kärcher Vacuum Cleaner when the container is full?
- P
  patrickroseAug 21, 2025
  If the suction turbine of your Kärcher Vacuum Cleaner won't switch off during wet vacuum cycles when the container is full, check or clean the electrode overflow fuse. Also, check the fluid level with non-conductive fluid. You may need an upgrade kit for 'non-conductive media' (2.641560.0). Finally, check or replace the PCB.
M
Maria PowellAug 26, 2025
How to restart the suction turbine on my Kärcher NT 40/1 Tact Te Vacuum Cleaner after emptying the container?
- M
  Matthew JonesAug 26, 2025
  If the suction turbine on your Kärcher Vacuum Cleaner doesn't start again after emptying the container, try turning off the appliance, waiting 5 seconds, and then turning it back on. Also, clean the electrodes and the space between them. You can also try releasing and removing the suction head, cleaning the electrodes, and then reinserting and locking the suction head.
J
John HerreraAug 30, 2025
Why can't I switch on the automatic filter cleaning on my Kärcher Vacuum Cleaner?
- C
  Christopher BrownAug 30, 2025
  If the automatic filter cleaning cannot be switched on on your Kärcher Vacuum Cleaner, check or replace the Tact filter cleaning system ON/OFF switch and check or replace the PCB.