Why does my Kärcher SGV 6/5 have no suction performance?
There could be several reasons for the lack of suction performance in your Kärcher Vacuum Cleaner. The accessories might be dirty, or the suction container/waste water container could be full or defective. Other potential causes include a dirty suction turbine, blower filter, or dirt filter for fresh water. Also, check if the reed contacts for the filling level are closed or active.
What to do if my Kärcher SGV 6/5 does not start?
If your Kärcher Vacuum Cleaner isn't starting, begin by checking the mains/fuse for the house connection and inspect the mains connection cable for any damage. Then, check the On/Off switch. Other possible solutions include checking the suction turbine, circuit board (check/replace), emptying the container (if wet vacuuming), checking the socket/microswitch, and checking/cleaning the overflow protection electrodes. Ensure the fusing isn't too low (under 16 amps).
How to fix no steaming function on Kärcher Vacuum Cleaner?
If your Kärcher Vacuum Cleaner isn't steaming, you should check the solenoid valve, ensure there is no water shortage, and inspect the steam gun. Also, verify the connection between the gun-hose-device is secure. Other possible causes include a tripped house fuse (overload), severely calcified steam boiler pipes, a defective steam boiler, or issues with the electronics, pipes, or connections. Ensure the fresh water container is properly seated and the selector switch is correctly positioned. A defective feed pump for fresh water or muddled switching positions (RESET) could also be the cause.
What to do if Kärcher Vacuum Cleaner displays service fault E01?
If your Kärcher Vacuum Cleaner displays a service fault E01, it indicates a water shortage on the water level probe or a defective probe. Check the water level. Also, check if the tank is seated correctly, inspect the boiler pump, and ensure the water hoses are properly installed without kinks.
What if display is on but pump isn't working on Kärcher SGV 6/5?
If the display is on but the pump isn't functioning on your Kärcher Vacuum Cleaner, check the fuse (Fuse 6.3A slow-blow) and replace it if it's defective.
What to do if Kärcher SGV 6/5 displays service fault 16?
If your Kärcher Vacuum Cleaner displays service fault 16, check the fan for soiling or damage. Also, check the connector and the plug contacts on the power electronics (power card). Inspect the ribbon cable that connects the power card with the µc-card; if defective, exchange the µc-card.
What to do if Kärcher SGV 6/5 displays service fault E12?
If your Kärcher Vacuum Cleaner displays service fault E12, check the connector plug "hand tool" on the device for proper seating and ensure it is completely dry.
What to do if Kärcher Vacuum Cleaner displays service fault E13?
If your Kärcher Vacuum Cleaner displays service fault E13, check the connector plug "hand tool" on the device for proper seating and ensure it is completely dry. If the issue persists, actuate the reset button on the µc-card.
What to do if Kärcher SGV 6/5 displays service fault E14?
If your Kärcher Vacuum Cleaner displays service fault E14, the steam boiler should be descaled.
What to do if Kärcher SGV 6/5 Vacuum Cleaner displays service fault E15?
If your Kärcher Vacuum Cleaner displays service fault E15, the steam boiler must be descaled.
General| Container capacity | 6 liters |
|---|---|
| Fresh water tank | 5 liters |
| Steam pressure | 6 bar |
| Power consumption | 3400 W |
| Voltage | 220-240 V |
| Frequency | 50-60 Hz |
| Hose length | 2.5 m |
| Maximum vacuum | 24 kPa |
| Tank capacity | 5 liters |
| Cable length | 7.5 meters |
To Next Page
