Why is my Kenmore Top load washer leaking water?
If you find water leaking from your Kenmore Top load washer, start by ensuring the washer is level to prevent water from splashing off the basket. Check that the fill hoses are tightly attached and that all four fill hose flat washers are properly seated. Also, ensure the drain hose is properly secured to the drainpipe or laundry tub. Check your household plumbing for leaks or clogs.
What to do if Kenmore Top load washer won't run or fill?
If your Kenmore Top load washer won't run or fill, or it stops working, or the wash light remains on, check the following: Ensure both water hoses are attached and have water flowing to the inlet valve, and that both hot and cold water faucets are turned on. Also, check for clogged inlet valve screens or kinks in the inlet hoses. Make sure the power cord is plugged into a grounded 3-prong outlet and that there is power to the outlet, resetting the circuit breaker if necessary. Ensure the lid is closed, as the washer will not run with it open. If the washer is tightly packed, remove several items and rearrange the load evenly.
What to do if Kenmore Top load washer is not draining or spinning?
If your Kenmore Top load washer is not draining or spinning, and loads are still wet, make sure to empty pockets and use garment bags for small items, as these can get caught in the pump. Using a cycle with a lower spin speed will also leave more water in the load. If the load is tightly packed or unbalanced, rearrange it evenly in the basket or select the Drain & Spin cycle to remove excess water.
Why is my Kenmore Top load washer not cleaning well?
If your Kenmore Top load washer isn't performing as expected and the load isn't completely covered in water, this is normal for an HE low-water washer. The washer senses load sizes and adds the correct amount of water. Do not add more water, as this can reduce cleaning effectiveness. You can use the Bulky/Bedding or Deep Wash cycle for a higher water fill.
Why is the lid locked light flashing on my Kenmore Top load washer?
If the lid locked light is flashing on your Kenmore Top load washer, make sure the lid is completely closed. The washer will not start or fill with the lid open. If a cycle was stopped or paused, the lid will not unlock until the basket has stopped spinning, which may take several minutes.
How to fix vibration or off-balance in Kenmore Top load washer?
If your Kenmore Top load washer is vibrating or off-balance, ensure the front and rear feet are in firm contact with the floor and that the washer is level. Also, check the floor for flexing or sagging; if uneven, use a 3/4" (19 mm) piece of plywood under the washer. Unbalanced loads can also cause this issue, so load dry items in loose heaps evenly around the basket wall. Avoid tightly packing the washer or washing single items, and use the Bulky/Bedding cycle for oversized items.
Why is my Kenmore Top load washer making noises?
If your Kenmore Top load washer is making unusual noises, it could be due to objects caught in the drain system. Make sure to empty pockets before washing, as loose items like coins could fall between the basket and tub or block the pump. It's also normal to hear metal items on clothing, such as snaps or zippers, touching the basket, or to hear the pump humming while draining water.
Why are there dry spots on clothes after Kenmore Top load washer cycle?
If you notice dry spots on your load after a cycle in your Kenmore Top load washer, it's likely due to the high spin speeds extracting more moisture. This is normal. If the washer is tightly packed, consider using the Bulky/Bedding or Deep Wash cycle. Avoid adding extra garments after the sensing/fill phase.
Why are the wash temperatures wrong on my Kenmore Top load washer?
If you're experiencing incorrect wash or rinse temperatures with your Kenmore Top load washer, ensure the hot and cold inlet hoses are not reversed and are properly attached to both the washer and faucet, with both hot and cold water flowing. Check that the inlet valve screens are not clogged and that there are no kinks in the hoses. Keep in mind that ENERGY STAR® qualified washers use cooler wash and rinse water temperatures.
Why is my Kenmore Top load washer not rinsing clothes properly?
If your load is not rinsed properly in your Kenmore Top load washer, ensure the hot and cold inlet hoses are not reversed and that both hoses are attached with water flowing. Check that the inlet valve screens are not clogged and that there are no kinks in the inlet hose. Make sure you are using HE detergent and not using too much, and load garments loosely around the basket wall. Avoid adding extra garments after the washer has started.
Essential precautions to reduce risk of fire, electric shock, or injury during washer use.
Addresses causes and solutions for washer vibration and unbalanced loads.
Explains common noises like clicking or humming and their possible causes.
Covers troubleshooting steps for water leaks, fill hoses, and drain connections.
Addresses common issues like not enough water or improper loading affecting performance.
Solutions for when the washer fails to start, fill, or stops mid-cycle.
Troubleshooting steps for issues with draining, spinning, and wet loads.
Solutions for the washer not cleaning effectively or removing stains.
Identifies causes of fabric damage and preventative measures during washing.
To Next Page
General