How to fix water leaks in a Kenmore 153.336162?
If your Kenmore Water Heater is leaking from improperly sealed connections, such as the hot or cold supply, relief valve, drain valve, or thermostat threads, try tightening these connections. Also, inspect other appliances near the water heater for leaks. If the issue is condensation, refer to the CONDENSATION section.
Why is the T&P valve leaking on my Kenmore 153.336162 and how to fix it?
If the T&P valve on your Kenmore Water Heater is leaking due to thermal expansion in a closed water system, install a thermal expansion tank. Do not plug the T&P valve. If the valve is improperly seated, check the relief valve for proper operation, again, do not plug the T&P valve.
How to troubleshoot a Kenmore 153.336162 Water Heater when the pilot won't light?
If your Kenmore Water Heater pilot will not light, turn on the main gas shutoff valve if the main gas supply is off. If the gas control knob is not positioned correctly, refer to the LIGHTING INSTRUCTIONS. Adjust the igniter tip if it is more than 1/8" from the pilot hood. Replace the pilot assembly if there is a thermocouple or thermocouple TCO malfunction. Reconnect the wire connector to the spark igniter if the wire is disconnected. Replace the pilot assembly if the electrode or electrical wire is broken. Replace the Piezo Igniter generator if it fails to operate or malfunctions. For melted insulation on the igniter wire or a high ambient room temperature, contact Sears Service to determine the cause.
What to do if the burner will not stay lit on my Kenmore Water Heater?
If the burner on your Kenmore Water Heater won't stay lit, replace the pilot assembly if there is a thermocouple TCO malfunction. Clean and reinstall the air intake screen if it is dirty or clogged. Replace the Gas Control if it is defective. Contact a service agency to determine the cause if there is a high ambient room temperature. Contact Sears Service to determine the cause if the flame arrestor openings are blocked.
Why does the pilot light keep going out on my Kenmore 153.336162?
If the pilot light keeps going out on your Kenmore Water Heater, clean the pilot assembly if the pilot burner is dirty. Also, clean and reinstall the air intake screen if it is dirty or clogged. Insert the thermocouple correctly if the thermocouple tip is not in contact with the pilot flame. Replace the pilot assembly if there is a thermocouple or thermocouple TCO malfunction. Replace the Gas Control if it is defective.
What to do if my Kenmore 153.336162 Water Heater is not producing enough hot water?
If you're not getting enough hot water from your Kenmore Water Heater, make sure the heater is lit and the thermostat is on. If not, refer to the LIGHTING INSTRUCTIONS. Ensure the thermostat isn't set too low by referring to TEMPERATURE REGULATION. If the heater is undersized, reduce hot water usage. For low gas pressure, contact your gas supplier. If the incoming water is unusually cold, allow more time for the heater to reheat. Have a plumber check and repair any leaks in hot water pipes or fixtures. If the high-temperature limit switch is activated, contact Sears Service to determine the cause.
How to get rid of smelly odors from a Kenmore 153.336162 Water Heater?
To address smelly odors from your Kenmore Water Heater, drain and flush the heater thoroughly, then refill if there is high sulfate or mineral content in the water supply. If bacteria are present in the water supply, chlorinate or aerate the water supply.
What to do if my Kenmore 153.336162 is producing water that is too hot?
Refer to TEMPERATURE REGULATION if your Kenmore Water Heater's thermostat is set too high.
Why is my Kenmore 153.336162 Water Heater making sizzling or rumbling noises?
To address sizzling or rumbling sounds in your Kenmore Water Heater, clean sediment from the tank. Refer to the DRAINING instructions in the Maintenance section of the manual.
General| Brand | Kenmore |
|---|---|
| Model | 153.336162 |
| Category | Water Heater |
| Language | English |
To Next Page