Kenmore 183.91579 - User Manual

Questions and Answers

G
Greg BushAug 19, 2025
Why is my Kenmore Beer Dispenser not running?
- H
  Hannah MyersAug 19, 2025
  Your Kenmore Beer Dispenser might not be running due to several reasons: it may not be plugged in properly, a fuse might be blown, the circuit breaker could be tripped, there might be a power outage, or it's plugged into a circuit with a ground fault interrupt. Ensure the plug is tightly pushed into the outlet. Check and replace the fuse with a 15 amp time delay fuse. Reset the circuit breaker. If there was a power outage, check your house lights or call your local Electric Company. Try using another circuit.
P
Peter HubbardAug 23, 2025
What to do if the Kenmore Beer Dispenser temperature is too warm?
- L
  Lawrence ThomasAug 23, 2025
  If the interior temperature of your Kenmore Beer Dispenser is too warm, it could be due to the temperature control being set too warm, the door being opened too frequently or kept open too long, a warm keg having been installed recently, or the dispenser having recently been disconnected. Turn the control to a colder setting and allow several hours for the temperature to stabilize. Open the door less often. Wait until the beer dispenser has had a chance to reach its selected temperature. It requires a few hours to cool down completely after being disconnected.
R
Richard ReyesAug 26, 2025
How to fix a Kenmore Beer Dispenser door that won't close?
- R
  robynhumphreyAug 26, 2025
  If the door of your Kenmore Beer Dispenser won't close, it might be because the dispenser isn't level, the floor is uneven, or there's a blockage. Level the dispenser using the adjustable leveling legs or move it to a different location. Adjust the keg to remove any blockage.
C
Cynthia BallardAug 28, 2025
How to adjust the temperature in a Kenmore Beer Dispenser if it's too cold?
- A
  Anthony NelsonAug 28, 2025
  If the interior temperature of your Kenmore Beer Dispenser is too cold, it's likely that the temperature control is set too low. Turn the control to a warmer setting. Allow several hours for the temperature to stabilize.
C
Cynthia CarrollAug 30, 2025
Why does moisture form on the inside walls of my Kenmore beer dispenser?
- J
  James SmithAug 30, 2025
  Moisture can form on the inside walls of your Kenmore beer dispenser due to hot and humid weather, which increases internal frost build-up, or because the door is kept open too long or opened too frequently. Opening the door less often can help.
R
Rachel BuchananSep 1, 2025
Why is the beer from my Kenmore dispenser flat?
- M
  Mallory WrightSep 1, 2025
  Flat beer from your Kenmore dispenser can be caused by a greasy glass, improper drawing of beer, or not enough pressure. Do not wash beer glasses together with glasses that have contained milk or any other fatty substance. Open the faucet quickly and completely. Increase the pressure if beer runs too slowly.
R
rcastanedaSep 3, 2025
Why is the beer from my Kenmore dispenser cloudy?
- M
  Maxwell ChandlerSep 3, 2025
  Cloudy beer from your Kenmore dispenser may be due to excessively low temperatures, particularly when the beer lies in the cold coil for long periods, or because the beer faucet was only opened partially. Make certain that the lines are thoroughly cleaned and then raise the temperature slightly. Open the faucet quickly and completely.
B
bonnie00Sep 5, 2025
How to get rid of odor in my Kenmore beer dispenser?
- G
  Gregory JacobsSep 5, 2025
  If there's an odor in your Kenmore beer dispenser, it likely means the interior needs to be cleaned. Clean the interior with a sponge, warm water, and baking soda.
K
Katherine RileySep 7, 2025
Why does moisture form on the outside of my Kenmore beer dispenser?
- A
  Amy SilvaSep 8, 2025
  Moisture forming on the outside of your Kenmore beer dispenser may be because the door isn't seating properly, causing cold air from inside to meet warm, moist air from outside.
S
smithcindySep 10, 2025
What causes off-taste beer in Kenmore dispenser?
- J
  jessicathompsonSep 10, 2025
  Off-taste beer in your Kenmore dispenser can result from improper cleaning of the tap, a contaminated air line, or using the wrong type of beer tube. Brush and clean the tap properly using a detergent, then rinse clean. The beer tube should be examined and replaced if contaminated. If you are using a rubber hose, try using a plastic tube instead.