What to do if my Kenmore 630.1395 does not start?
If your Kenmore Dishwasher doesn't start, make sure the door is completely shut. Press the main power switch to turn the unit on. Check the circuit breaker. Select a cycle and close the door. Check and turn on the water supply. To reset the dishwasher, refer to the 'Canceling or changing the cycle' or 'Delay Start' section in this manual.
Why can't I select the desired cycle on my Kenmore 630.1395 Dishwasher?
If you're unable to select the desired cycle on your Kenmore Dishwasher, ensure the previous cycle has finished.
Why didn't my Kenmore Dishwasher sanitize?
To ensure your Kenmore Dishwasher sanitizes, select a cycle intended for sanitizing and do not open the door while the wash cycle is running.
Why won't the detergent dispenser cover shut on my Kenmore 630.1395 Dishwasher?
If the detergent dispenser cover on your Kenmore Dishwasher won't shut, refer to the 'Adding Detergent and Rinse Aid' section for instructions on opening and closing the dispenser. Also, ensure the previous cycle has finished, been reset, or wasn't interrupted.
What to do about noise during Kenmore 630.1395 Dishwasher wash cycle?
Water circulation sound is normal during a Kenmore Dishwasher wash cycle. However, if you suspect items are banging into each other or the spray arms, refer to the 'Preparing and Loading' section for optimal arrangement.
How to prevent etching on glassware in my Kenmore 630.1395?
To prevent etching on glassware in your Kenmore Dishwasher, ensure your glasses are dishwasher safe and select a cycle that doesn't get too hot. Avoid using the heated dry option. Adjust the amount and type of detergent based on water hardness and food soil. If you pre-rinse dishes or have soft water, use less detergent.
How to get rid of odor in Kenmore 630.1395?
To eliminate odor in your Kenmore Dishwasher, remove food debris from the bottom of the dishwasher. Ensure the unit has completely drained after the last cycle. For drain hose obstructions, contact qualified personnel.
Why is the display not illuminating on my Kenmore 630.1395?
If the display on your Kenmore Dishwasher isn't illuminating, a fuse may have blown or the circuit breaker tripped. Check the fuse or circuit breaker box and replace the fuse or reset the breaker if necessary. Also, ensure the door is properly latched and completely closed.
Why does my Kenmore 630.1395 run for so long?
Several factors can cause your Kenmore Dishwasher to run longer. The incoming water may not be warm enough; run the hot water faucet at the sink nearest to the dishwasher until the water reaches 120°F before starting a cycle. Cycle time can also vary based on soil and water conditions, as sensors automatically increase the cycle time when heavy soil is detected. Ensure the rinse agent dispenser is full and verify the dishwasher is connected to the hot water supply.
Why is my Kenmore 630.1395 not draining?
If your Kenmore dishwasher isn't draining, inspect the drain hose for kinks or crushing, ensuring proper installation. Ensure a portion of the drain hose is at least 20 inches from the floor. If connected to a food disposer, verify the plug was removed. Clean the air gap periodically to ensure proper drainage.
Essential safety advice for operating the dishwasher safely.
Guidelines on grounding, proper use, and handling of items.
Advice on loading, door operation, and protecting the unit.
How to cancel/change cycles, use indicators like Sanitized and Rinse Aid.
Instructions for cleaning spills, inner door, drain air gap, and spray arms.
Solutions for dishwasher not starting or running improperly.
Addresses issues with dishes not getting clean or dry.
Resolving problems with filling, leaks, suds, odor, tub stains, and noise.
General| Type | Built-In |
|---|---|
| Control Type | Electronic |
| Number of Wash Cycles | 6 |
| Place Settings | 14 |
| Energy Star Certified | Yes |
| Heated Dry | Yes |
| Third Rack | No |
| Stainless Steel Tub | Yes |
| Soil Sensor | Yes |
| Delay Start | Yes |
| Color | White |
| Wash Cycles | Heavy, Normal, Light, Rinse |
| Noise Level | 52 dBA |
To Next Page