How to fix a DRAIN ERROR on my Kenmore 796.4044*9 Washer?
If your Kenmore Washer displays a DRAIN ERROR, it means the water was not fully drained within 10 minutes. Inspect the drain hose and filter for any clogs and remove them.
How do I troubleshoot a LOCKED MOTOR ERROR on my Kenmore 796.4044*9 Washer?
If your Kenmore Washer displays a LOCKED MOTOR ERROR, first reconnect the connector in the MOTOR HARNESS. If the issue persists, inspect and clean the connections. If that doesn't work, repair or replace the MOTOR HARNESS. If the problem continues, the hall sensor may be defective and need to be replaced.
What should I do if my Kenmore 796.4044*9 Washer has a POWER FAILURE?
If your Kenmore Washer experienced a POWER FAILURE, check the power supply and ensure it is stable.
Why does my Kenmore 796.4044*9 Washer show an UNBALANCE ERROR?
If your Kenmore Washer displays an UNBALANCE ERROR, it could be due to several reasons. First, if the load is too small, add more laundry to the drum. Second, make sure the appliance is level on the floor. Third, redistribute the laundry evenly if it's gathered to one side. Lastly, remove any non-distributable items from the drum.
What to do if my Kenmore 796.4044*9 Washer shows a DOOR OPEN ERROR?
If your Kenmore Washer displays a DOOR OPEN ERROR, first ensure the door is fully closed. If the issue persists, check and secure any loose electrical connections at the Door switch and PWB Assembly. If neither of those fixes the issue, the DOOR SWITCH ASSEMBLY may be out of order and need to be replaced.
What to do if my Kenmore Washer displays a WATER INLET ERROR?
If your Kenmore Washer is showing a WATER INLET ERROR, ensure that the water supply is adequate and check for any obstructions in the water inlet. This error indicates that the correct water level was not reached within 8 minutes after water was supplied, or it did not reach the preset water level within 25 minutes.
What causes an OVER FLOW ERROR on my Kenmore Washer?
If your Kenmore Washer displays an OVER FLOW ERROR, there may be an issue with the water level sensor or the drainage system. This error indicates that the water is overflowing because the water level frequency is over 213. Check these components to resolve the problem.
What does a PRESSURE SENSOR ERROR mean on my Kenmore 796.4044*9?
If your Kenmore Washer displays a PRESSURE SENSOR ERROR, the SENSOR SWITCH ASSEMBLY is out of order. Replace the SENSOR SWITCH ASSEMBLY to resolve this issue.
What to do if my Kenmore 796.4044*9 shows a HEATING ERROR?
If your Kenmore Washer displays a HEATING ERROR, the THERMISTOR is out of order. To fix this, replace the THERMISTOR.
What does EEPROM ERROR mean on my Kenmore Washer?
If your Kenmore Washer displays an EEPROM ERROR, the EEPROM is out of order, and you should replace it.
General| Brand | Kenmore |
|---|---|
| Energy Star Certified | Yes |
| Number of Temperature Settings | 5 |
| Voltage | 120V |
| Frequency | 60 Hz |
| Model Number | 796.4044*9 |
| Color | White |
| Width | 27 in |
| Height | 39 in |
Details key features of the washing machine, including drum capacity, drive system, and control lock.
Explains how water temperature, selected temperature, and load size determine optimal washing time.
Describes the pressure sensor system used to manage water levels in the tub.
Details how the door operates, including locking, unlocking, and power failure behavior.
Lists conditions under which the washing machine door cannot be opened.
Explains how to use the control lock to prevent unintended changes during operation.
Lists and illustrates various accessories provided with the washing machine.
Provides guidelines for removing shipping bolts, installing the appliance on a flat surface, and leveling.
Details the functions of buttons, indicators, and the display on the control panel.
Presents recommended fabric types, default settings, and available options for each wash cycle.
Explains specific cycle options like Stain Treat, 2nd Rinse, Add Steam, Delay Start, Clean Washer, and Control Lock.
Describes the sequence of operations for various washing and spinning processes.
Highlights safety precautions when performing troubleshooting tests.
Details how to enter and operate the load test mode for diagnostics.
Explains the procedure to check water level frequency using specific button combinations.
Emphasizes safety precautions during troubleshooting and repair.
Provides a quick reference for common error codes, symptoms, and causes.
Presents a circuit diagram and key test points for troubleshooting.
Guides users through diagnosing and resolving specific error codes displayed by the washer.
Provides steps to diagnose and fix a heating error in the washing machine.
Outlines the procedure to troubleshoot a locked motor error.
Details the steps for troubleshooting a door open error.
Explains how to resolve unbalance errors related to load distribution or machine leveling.
Guides on troubleshooting and fixing overflow errors in the washing machine.
Details the troubleshooting steps for a pressure sensor error.
Covers troubleshooting for issues not related to specific error codes.
Provides steps to diagnose and resolve issues where the washer has no power.
Guides on troubleshooting when buttons on the control panel do not work.
Addresses issues related to excessive vibration or noise during the spin cycle.
Explains how to troubleshoot problems with detergent not flowing into the dispenser.
Guides on resolving issues with liquid detergent, softener, or bleach not flowing correctly.
Provides steps to diagnose the cause of abnormal sounds from the washing machine.
Details the testing procedure and expected resistance values for the line filter.
Explains how to test the door lock switch assembly and its components.
Provides testing procedures for the stator assembly, including windings and hall sensor.
Details the testing of drain and circulation pump motors, including resistance checks.
Explains how to test the inlet valve assembly, including resistance measurements.
Details the testing procedures for the wash heater and steam generator heater.
Provides information on testing wash and steam generator thermistors, including resistance values.
Step-by-step guide for disassembling the control panel assembly.
Instructions for removing and disassembling the main Printed Wiring Board assembly.
Details the process for disassembling the detergent dispenser assembly.
Instructions for disassembling the noise filter unit.
Step-by-step guide for removing the cabinet cover of the washing machine.
Provides instructions for disassembling the washing machine door.
Details the process for disassembling the door lock switch assembly.
Instructions for disassembling the circulation and drain pump.
Details the steps for removing the heater assembly from the tub.
Instructions for disassembling the thermistor from the washing machine.
Provides instructions for disassembling the motor and damper components.
Illustrates the exploded view of the cabinet and control panel components.
Shows the exploded view of the drum and tub assembly parts.
Provides an exploded view of the detergent dispenser assembly components.
To Next Page