EasyManua.ls Logo

Kenwood K1014WM18 - User Manual

Kenwood K1014WM18
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
10KG washing machine
K1014WM18
installation / instructions manual
Kenwood 10kg Washing Machine K1014WM18 Manual.indd 1 21/06/2018 08:17

Table of Contents

Questions and Answers

  • M
    mallorywilliamsAug 15, 2025
    Why Kenwood Washer won't start?
    • D
      ddayAug 15, 2025
      Your Kenwood Washer might not start due to several reasons: it may not be plugged in, the fuse might be blown, there could be a power cut, the Start/Pause button might not be pressed, the door might not be closed properly, or the program dial is in the stop position. To resolve this, ensure the washer is plugged in and switched on, replace the fuse if necessary, check the mains power, press the Start/Pause button, close the door properly, and turn the program dial to the desired position.
  • D
    Diane AlvaradoAug 18, 2025
    What to do if my Kenwood Washer vibrates?
    • D
      daniel11Aug 18, 2025
      If your Kenwood washer is vibrating, it could be due to the machine not being level, transit bolts still in place, a very small load causing an unbalanced drum, or the machine being overloaded or not loaded correctly. Try adjusting the feet to level the machine, removing the transit bolts, adding more laundry for balance, or removing some laundry and loading the drum correctly.
  • S
    Sara WrightAug 22, 2025
    Why Kenwood K1014WM18 Washer does not intake water?
    • V
      vickieharrisAug 22, 2025
      If your Kenwood Washer isn't intaking water, the water tap might be turned off, the water inlet hose could be twisted or clogged, the valve inlet filter might be clogged, or the door might not be closed properly. Ensure the water tap is on, check and untwist the water inlet hose, clean the water inlet hose filters and valve inlet filters, and make sure the door is closed properly.
  • J
    Jason ThomasAug 25, 2025
    What to do if Kenwood K1014WM18 Washer does not discharge water?
    • M
      Miranda VasquezAug 26, 2025
      If your Kenwood Washer isn't discharging water, the discharging hose might be clogged or twisted, or the pump filter might be clogged. Check the discharging hose and either clean or untwist it. Also, clean the pump filter.
  • K
    Kelly GarciaAug 28, 2025
    Why spinning operation is not performed or runs late in my Kenwood K1014WM18?
    • S
      sandy80Aug 28, 2025
      The spinning operation in your Kenwood Washer may not be performed or runs late because the unbalanced load control system has been activated. This system will try to spread your laundry by tumbling for a while, and the spinning operation will begin after your laundry is spread. Place the laundry in the machine in a balanced fashion the next time.
  • J
    Jeff FergusonAug 31, 2025
    Why is there excessive foam in the detergent drawer of my Kenwood K1014WM18 Washer?
    • D
      David AndersenAug 31, 2025
      Excessive foam in the detergent drawer of your Kenwood Washer is likely due to using too much detergent or using the wrong detergent. To eliminate foam formation, press the Start/Pause button, mix a spoon of softener with half a liter of water, and pour the mixture into the detergent drawer. After 5-10 minutes, press the Start/Pause button again. In your next wash, adjust the detergent dose accordingly. Also, ensure you are only using detergents produced for automatic washing machines.
  • B
    Bridget ChandlerSep 4, 2025
    Why Kenwood K1014WM18 Washer gives unsatisfactory washing result?
    • N
      Nicholas LopezSep 4, 2025
      An unsatisfactory washing result from your Kenwood Washer may occur if your laundry is too soiled for the chosen wash program, the amount of detergent used is insufficient, the machine is overloaded, the water in your area is very hard, or you have not loaded your laundry evenly. Choose a suitable program, adjust the amount of detergent, load the correct weight of laundry, consider increasing detergent for hard water, and load your laundry correctly.
  • R
    Ryan CainSep 7, 2025
    Why does the laundry have detergent residue after washing in my Kenwood K1014WM18?
    • M
      Melissa ClarkSep 8, 2025
      Detergent residue on laundry after washing with your Kenwood Washer is likely due to non-dissolving particles of some detergents sticking to the laundry, appearing as white spots. Perform an extra rinse by setting your machine to the 'Rinse' program, or clean the spots using a brush after your laundry is dry.
  • M
    Michelle ThomasSep 12, 2025
    Why do grey spots appear on the laundry after washing in my Kenwood K1014WM18?
    • W
      William Patton DVMSep 12, 2025
      Grey spots appearing on laundry after washing in your Kenwood Washer may be due to oil, cream, or ointment. Apply the maximum amount of detergent instructed by the detergent manufacturer in the next washing operation.

Kenwood K1014WM18 Specifications

General IconGeneral
Washing Capacity10 kg
Spin Speed1400 rpm
Capacity10 kg
Energy RatingA+++
ColorWhite
Loading TypeFront Load

Related product manuals