To Next PageTo Next PageWhat to do if my Kenwood Car Receiver sound cannot be heard?
If you cannot hear any sound from your Kenwood Car Receiver, try these solutions: First, adjust the volume to make sure it's at an audible level. Next, inspect the cords and connections to ensure they are properly connected. Finally, clean the connectors to remove any dirt or debris that might be interfering with the sound.
What to do if Bluetooth pairing cannot be made on Kenwood Car Receiver?
If you're having trouble pairing a Bluetooth device with your Kenwood Car Receiver: * Ensure you've entered the same PIN code on both devices. * Try deleting the pairing information from both the receiver and the Bluetooth device, and then attempt the pairing process again.
What to do if setting/deleting the remote control ID is unsuccessful on Kenwood Car Receiver?
If setting or deleting the remote control ID is unsuccessful and you see “SET ERROR” or “DEL ERROR” on your Kenwood Car Receiver, turn the power off, then turn it back on, and try the operation again.
Why does my Kenwood Car Receiver say 'MISWIRING CHECK WIRING THEN PWR ON'?
If your Kenwood Car Receiver displays the message “MISWIRING CHECK WIRING THEN PWR ON”, turn the power off. Then, check to ensure the terminals of the speaker wires are properly insulated. Turn the power back on.
What does “CHECK ANTENNA” mean on my Kenwood Car Receiver and how to fix it?
If your Kenwood Car Receiver displays “CHECK ANTENNA”, it means you should check that the antenna and its connection are in good condition.
What to do if my Kenwood Car Receiver disc cannot be ejected?
If the disc cannot be ejected from your Kenwood Car Receiver, press and hold the M button to forcibly eject the disc, being careful not to drop it. If this does not solve the problem, reset the unit.
Why does my Kenwood Car Receiver say “NO SIGNAL”?
If your Kenwood Car Receiver displays “NO SIGNAL”, make sure the antenna is mounted outside the vehicle.
What does “NO MUSIC” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “NO MUSIC”, connect a USB device that contains playable audio files.
How to fix echo or noise during a phone conversation on my Kenwood Car Receiver?
If you experience echo or noise during phone conversations using your Kenwood Car Receiver, try the following: 1. Adjust the microphone unit’s position. 2. Check the [ECHO CANCEL] setting.
What does “USB HUB IS NOT SUPPORTED” mean on Kenwood Car Receiver?
If your Kenwood Car Receiver displays “USB HUB IS NOT SUPPORTED”, it means that the unit cannot support a USB device connected via a USB hub.
General| Brand | Kenwood |
|---|---|
| Model | KDC-MP372BT |
| Type | Car Receiver |
| Bluetooth | Yes |
| USB Port | Yes |
| Aux Input | Yes |
| CD Playback | Yes |
| Radio Tuner | AM/FM |
| Display Type | LCD |
| Subwoofer Control | Yes |
| Preset EQ | Yes |
| Remote Control | Yes |
| Max Power Output | 50W x 4 |
| RMS Power Output | 22W x 4 |
| Media Playback | MP3, WMA |
| EQ Settings | 13-Band Graphic EQ |
Warns against distracted driving and hazards of battery ingestion, especially for children.
Identifies controls on the unit's front panel for power, volume, source selection, and display.
Describes the remote control, its sensor, and provides instructions for replacing its battery.
Guides setting display language and disabling the demonstration mode for initial setup.
Explains how to adjust the clock format (12H/24H) and set the current date.
Details how to configure initial settings like Audio Control and Preset Type.
Explains how to search for stations manually, automatically, or via presets using BAND and SEEK.
Explains how to search for radio stations by Program Type (PTY) and language.
Instructions for playing audio CDs, including playback controls like pause, track selection, and repeat.
Guides connecting USB devices for playing MP3/WMA/AAC/WAV/FLAC files and managing tracks.
Details connecting iPod/iPhone and Android devices for playback and control via USB.
Describes Quick, Skip, and Alphabet searches for locating media files efficiently.
Instructions for preparing, connecting, and starting Pandora playback via USB.
Guides creating, saving, searching, and deleting Pandora stations.
Steps to prepare, connect, and begin listening to iHeartRadio via USB.
Instructions for preparing, connecting, and starting Spotify playback via USB.
Steps for connecting the tuner, checking Radio ID, and activating subscription.
How to select channels, browse, and use direct access tuning for SiriusXM.
Explains channel and replay keymodes for controlling SiriusXM, including stored channels.
Details features for storing favorite channels and starting songs from the beginning.
Covers locking channels, setting passcodes, and editing channel locks for parental control.
Lists supported Bluetooth profiles (HFP, A2DP) and codecs (SBC, AAC) for device compatibility.
Steps to pair a Bluetooth device with the unit for the first time using Secure Simple Pairing.
Describes automatic pairing upon connection and handling incoming calls.
Guides making calls from call history, phonebook, number dial, or voice commands.
Details accessing the phonebook, searching contacts, and dialing numbers.
Activating voice recognition and storing contacts in memory for quick dialing.
Covers device connection modes, selecting audio devices, and deleting paired devices.
Checks connectivity of Bluetooth profiles between device and unit.
Instructions for connecting and playing audio from a Bluetooth device.
Guides setting up the app for iPhone/iPod or Android via Bluetooth.
How to listen to iPhone/iPod music or internet radio via Bluetooth.
Guides setting speaker delay and gain based on listening position and car type.
Guides on resolving Bluetooth pairing, call quality, and device detection issues.
