To Next PageTo Next Page
Need help?Do you have a question about the Kenwood KRF-A4020 and is the answer not in the manual?
AM Tuner Section| tuning frequency range | 531 kHz ~ 1, 602 kHz |
|---|---|
| usable sensitivity | 16 µV / (600 µV/m) |
| signal to noise ratio | 50 dB |
General| power consumption | 280 W |
|---|---|
| switched AC outlet | 2 (total 150 W max.) |
| dimensions (W x H x D) | 440mm x 144mm x 390mm |
| weight | 8.0 kg |
Audio Section| rated power output (STEREO operation, DIN) | 1 kHz, 0.7 % at 4 Ω. 105 W + 105 W |
|---|---|
| rated power output (STEREO operation, IEC) | 63 kHz ~ 12.5 kHz, 0.5 % at 4 Ω. 100 W + 100 W |
| total harmonic distortion | 0.02 % (1 kHz, 50 W, 4 Ω) |
| signal to noise ratio (PHONO) | 75 dB (IHF'66) |
| signal to noise ratio (CD) | 92 dB (IHF'66) |
| input sensitivity / impedance (PHONO) | 2.5 mV / 27 kΩ |
| input sensitivity / impedance (CD) | 200 mV / 47 kΩ |
| output level / impedance (TAPE REC) | 200 mV / 2.2 kΩ |
| output level / impedance (PRE OUT) | 2 V / 2.2 kΩ |
| bass tone control | ±9 dB (at 100 Hz) |
| treble tone control | ±9 dB (at 10 kHz) |
FM Tuner Section| tuning frequency range (U.K. and Europe) | 87.5 MHz ~ 108.0 MHz |
|---|---|
| tuning frequency range (Russia) | 87.5 MHz ~ 108.0 MHz (10 kHz STEP), 65.0 MHz ~ 74.0 MHz (50 kHz STEP) |
| usable sensitivity (MONO) | 1.2 µV / 13.2 dBf (40 kHz DEV., S/N 26 dB) |
| usable sensitivity (STEREO) | 45 µV / 44.2 dBf (46 kHz DEV., S/N 46 dB) |
| total harmonic distortion (MONO) | 0.2% (65.2 dBf input) |
| total harmonic distortion (STEREO) | 0.8% (65.2 dBf input) |
| signal to noise ratio (MONO, U.K. and Europe) | 65 dB (40 kHz DEV., S/N 26 dB, 65.2 dBf input) |
| signal to noise ratio (STEREO, U.K. and Europe) | 58 dB (46 kHz DEV., S/N 46 dB, 65.2 dBf input) |
| signal to noise ratio (MONO, Russia) | 63 dB (40 kHz DEV., S/N 26 dB, 65.2 dBf input) |
| signal to noise ratio (STEREO, Russia) | 58 dB (46 kHz DEV., S/N 46 dB, 65.2 dBf input) |
| stereo separation | 36 dB |
| selectivity | 64 dB |
| frequency response | +0.5 dB ~ –3.0 dB (30 Hz ~ 15kHz) |
Procedure to reset the microcomputer to restore normal operation.
Details initial settings, backup procedures, and tuner destination lists.
Describes test modes for tuner and amplifier functions, including active contents.
Explains the microprocessor and its peripheral block diagram.
Details the function and I/O for each pin of the main microprocessor.
Adjustment procedures for FM sections excluding specific types.
Adjustment procedures specific to E, T, and Q types of FM sections.
Adjustment procedures for the audio section, including idle current.
Component layout diagram for the Tuner unit.
Component layout diagram for the Audio unit.
Technical specifications for US and Canadian models.
Technical specifications for models sold in other countries.
Technical specifications specific to UK and European models.
