EasyManua.ls Logo

Kenwood X802-5 - User Manual

Kenwood X802-5
10 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
X802-5
XM802-5
CLASS D FIVE CHANNEL POWER AMPLIFIER
INSTRUCTION MANUAL
AMPLIFICATEUR DE PUISSANCE 5 CANAUX CLASSE D
MODE D’EMPLOI
AMPLIFICADOR DE POTENCIA DE 5 CANALES CLASE D
MANUAL DE INSTRUCCIONES
Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from
your new power amplier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the
space provided below. Refer to the model and serial numbers whenever you call upon your Kenwood dealer for
information or service on the product.
Model X802-5 /XM802-5 Serial number
US Residence Only
Register Online
Register your Kenwood product at w
ww.kenwood.com/usa
B5A-3472-10 / 01 (KN / WN)© 2021 JVCKENWOOD Corporation
248 mm (9-3/4)
53 mm
(2-1/16)
169 mm (6-5/8)
Accessories / Accessoires / Accesorios
①
Ø4×16 mm
Self-tapping screws
Vis taraudeuses
Tornillo autorroscantes
4
②
Speaker level input cable
Câble d’entrée de niveau d’enceinte
Cable de entrada del nivel de altavoces
1
Dimensions / Dimensions / Dimensiones
KENWOOD
JVCKENWOOD Corporation
■
11
■
@
""
/
@
'W
KIMV00D
@
/
"
@

Table of Contents

Questions and Answers

  • M
    mleeJul 29, 2025
    What to do if my Kenwood X802-5 Amplifier has no sound?
    • T
      theresasmithJul 30, 2025
      If your Kenwood Amplifier has no sound, or sound from only one side, and you suspect a blown fuse, here's what to check: * Ensure all input and output cables are securely connected. * The protection circuit might be activated; review the section on the protection function for guidance. * If the volume was too high, replace the fuse and reduce the volume. * Inspect the speaker cord for shorts; fix any shorts and then replace the fuse.
  • T
    Tammie AllenAug 12, 2025
    Why is the sound quality bad on my Kenwood X802-5?
    • Z
      zgutierrezAug 13, 2025
      If the sound quality from your Kenwood Amplifier is poor or distorted: * Verify that the speaker wires are connected with the correct polarity, carefully checking the positive and negative terminals and wires. * Ensure that no speaker wire is pinched by a screw in the car body; reconnect the wire to avoid any pinching. * Confirm that all switches are set correctly, consulting the “Controls” section for proper settings.

Summary

Safety Precautions

Injury, Fire, and Damage Prevention

Covers preventing injury, fire, and damage to the unit.

Protection Circuit and Operation

Wiring and Speaker Compatibility

Installation Guide

Amplifier Installation Procedure

Outlines the sequence for installing the amplifier in a vehicle.

Installation Location Recommendations

Connection and Wiring

Power, Speaker, and Bridged Wiring

Speaker Output Options

Input Connectivity and Cable Identification

Unit Controls and Features Overview

Power, Ground, and Speaker Terminals

Identifies and describes the unit's power, ground, and speaker output connections.

Input, Sensitivity, and Signal Adjustment Controls

Details input sensitivity, selector, bass boost, and filter controls.

Troubleshooting Common Issues

No Sound or Output Level Problems

Sound Quality and Distortion Issues

Technical Specifications

Audio Performance Specifications

Details power output, impedance, frequency response, sensitivity, and S/N ratio.

General Unit Specifications

Covers operating voltage, current consumption, dimensions, weight, and compliance standards.

Kenwood X802-5 Specifications

General IconGeneral
BrandKenwood
ModelX802-5
CategoryAmplifier
LanguageEnglish

Related product manuals