Kenwood XM160-2 User Manual

Take the time to read through this instruction manual.
Familiarity with installation and operation procedures will help you obtain the best performance from your new power amplier.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty card, and in the space provided below. Refer to the
model and serial numbers whenever you call upon your KENWOOD dealer for information or service on the product.
Model XM160-2 Serial number
© 2023 JVCKENWOOD Corporation
XM160-2
2-CHANNEL POWER AMPLIFIER DESIGNED AND ENGINEERED TO BE
PLUG AND PLAY FOR 2014-UP HARLEY-DAVIDSON® ROAD GLIDE®,
STREET GLIDE®, OR ULTRA MOTORCYCLES
INSTRUCTION MANUAL
JVCKENWOOD Corporation
US Residents Only
Register Online
Register your KENWOOD product at https://registerkenwood.us.jvckenwood.com/

Kenwood XM160-2 Specifications

General

Channels	2
Frequency Response	5Hz - 50kHz
Signal to Noise Ratio	100 dB
THD at 4-Ohm RMS Power	0.08%
RMS Power at 4 Ohms	60 Watts x 2
RMS Power at 2 Ohms	80 Watts x 2
Bridged RMS Power at 4 Ohms	160W x 1
Input Sensitivity	0.2 - 5.0 V

Summary

KENWOOD XM160-2 Amplifier Manual

Product Introduction and Records

Overview, manual identification, and section for recording serial numbers.

Safety Precautions and Guidelines

Critical safety warnings, protection features, and speaker selection advice.

Installation: Street/Ultra Glide Models

Detailed steps for installing the amplifier in Street/Ultra Glide motorcycles.

Installation: Road Glide Models

Detailed steps for installing the amplifier in Road Glide motorcycles.

Adding a Second Amplifier

Instructions for installing an additional XM160-2 amplifier.

Final System Adjustments

Steps for fine-tuning the audio system after installation.

Limited Warranty Information

Details on warranty coverage, exclusions, and how to obtain service.

Important Notes and FCC Compliance

General notes, FCC regulations, and compliance information.

KENWOOD XM69R Speaker Manual

XM69R Product Overview and Records

Manual identification and section for recording serial numbers.

XM69R Safety and Installation Precautions

Safety advice specific to XM69R speaker installation and use.

Installation: CA-CUT14 Lid Kit

Guide to installing XM69R speakers into CA-CUT14 saddlebag lids.

Installation: CA-LID98 Lids

Instructions for installing XM69R speakers into CA-LID98 saddlebag lids.

Installation: Other 6" x 9" Lids

Guide for fitting XM69R speakers into alternative saddlebag lids.

Warranty Information

Details on warranty coverage, exclusions, and service procedures.

KENWOOD XM65F/XM65R Speaker Manual

XM65F/XM65R Product Overview and Records

Manual identification and section for recording serial numbers.

XM65F/XM65R Safety and Installation Notes

Safety guidelines for installing XM65F and XM65R speakers.

XM65F Installation: FLH (Batwing) Models

Step-by-step guide for installing XM65F speakers in FLH models.

XM65F Installation: Road Glide Models

Guide for installing XM65F front speakers specifically for Road Glide models.

XM65R Installation: Rear Speakers

Instructions for installing XM65R rear speakers.

Warranty Information

Details on warranty coverage, exclusions, and service procedures.

KENWOOD CA-CUT14 Lid Kit Manual

CA-CUT14 Installation Overview

Overview of the CA-CUT14 lid kit installation process.

CA-CUT14 Safety Precautions

Safety warnings and material notes for the CA-CUT14 lid kit.

CA-CUT14 Getting Started

Initial steps and preparation for installing the CA-CUT14 kit.

CA-CUT14 Disassembling Factory Lid

Procedures for safely removing and disassembling the factory saddlebag lid.

CA-CUT14 Mounting Templates

Guide on using templates for accurate cutting of the saddlebag lid.

CA-CUT14 Cutting Grille Opening

Instructions for cutting the necessary opening for speaker grilles.

CA-CUT14 Fitting Grille and Adapters

Steps for fitting speaker adapters and grilles onto the lid.

CA-CUT14 Wiring Saddlebags for Speakers

Instructions for wiring the saddlebags to accommodate speakers.

CA-CUT14 Wiring Amplifier to Saddlebags

Steps to connect the amplifier to the saddlebag speaker wiring.