Brew Your First Coffee
Make Your First Latte
Place Mug & Pod
Place a mug on the drip tray plate. If using a
travel mug, remove the drip tray and place the
mug on the drip tray base. Lift the handle and
place a K-Cup® pod in the K-Cup® pod holder.
Lower the handle completely to close the lid.
Do not remove the foil lid on the K-Cup® pod.
High Altitude Brewing: While holding the brewer
handle up, push down slowly on the K-Cup® pod
in the pod holder until the bottom of the K-Cup®
pod is punctured by the exit needle.
Fill Frother
Remove lid and add chilled milk to the MAX line
marked in the frother. Replace the lid and place
the frother on the frother base.
Press the power button on the frother.
The button will illuminate while heating –
approximately 3 minutes. Frothing is complete
when the button flashes and then turns off.
CAUTION: Frother is not microwave or dishwasher safe.
NOTE: Do not under or overfill frother. Do not operate before adding milk.
Brew a Shot
The three brew buttons and SHOT button
will blink. Press the SHOT button. Brewing is
complete when the SHOT button is no longer
illuminated.
NOTE: After 60 seconds, the brew buttons will be disabled. To
re-activate, lift and lower the handle completely.
CAUTION: While brewing, there is extremely hot water in the K-Cup®
pod holder. To avoid injury, do not lift the handle during the brewing
process.
Place Mug & Pod
Place a mug on the drip tray. Lift the handle
and place any K-Cup® pod in the K-Cup® pod
holder. Lower the handle completely to close the
lid.
Do not remove the foil lid on the K-Cup® pod.
Create your Latte
Remove the frother from the base. Remove the
lid and pour the frothed milk over your shot of
coffee.
NOTE: Clean frother immediately after use. For cleaning instructions,
see Caring for your Brewer section in this guide.
Brew & Enjoy!
Select your brew size. The button will remain
illuminated while brewing – about 1 minute.
Brewing is complete when the button is no longer
illuminated. Lift the handle and dispose of the
used K-Cup® pod.
The brewer will be ready to brew another cup in
about a minute.
NOTE: After 60 seconds, the brew buttons will be disabled. To re-activate,
lift and lower the handle completely.
CAUTION:
While brewing, there is extremely hot water in the K-Cup® pod
holder. To avoid injury, do not lift the handle during the brewing process.
11
3
2 4
2
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Brewer Features
Frother froths milk to create your favorite latte.
SHOT button brews a shot of coffee to make
delicious, creamy lattes.
Smart Start heats then brews in one simple
process. No need to wait for the brewer to heat
before selecting brew size. Power on your brewer,
place mug, insert a K-Cup® pod, and lower the
handle. Then, select your brew size. The brewer
will heat, then automatically begin brewing.
Auto Off automatically turns your brewer off
2 hours after the last brew for energy savings.
Caring for your Brewer
Regular cleaning keeps your brewer running smoothly.
Always be sure to turn off and unplug your brewer
before cleaning. For detailed brewer cleaning and
maintenance instructions, videos, and the full Use &
Care guide, visit support.keurig.com. Beyond these
recommended cleaning instructions, this brewer is not
user-serviceable. For service, please refer to the
Warranty included with your brewer.
Frother
Clean immediately after each use and before first use.
To Clean:
1. Remove frother from the base, remove silicone ring
from lid, and remove the whisk from inside the frother.
2. Wash the silicone ring, lid, and whisk with warm,
soapy water.
3. Clean the interior of the frother with soap and rinse
with warm water. Use a soft, non-abrasive cloth or
sponge to prevent damaging the inner coating.
4. Wipe the exterior with a soft, damp cloth.
5. Dry all parts thoroughly and reassemble for next
use.
Note: Frother is not dishwasher safe. Do not submerge frother in water. Only use
non-abrasive cleaning materials to prevent damage to the inner surface of the
frother.
Water Reservoir
The water reservoir lid and water reservoir should
be cleaned periodically. Clean in a dishwasher
(top rack only) or hand wash. To hand wash, use
a damp, soapy, non-abrasive cloth. Rinse the
reservoir thoroughly after cleaning. This will
ensure that no cleaning solutions remain in the
area as they may contaminate the water supply.
After rinsing, fill the reservoir with clean water
and return it to the brewer. Do not dry the inside
of the water reservoir with a cloth as lint may
remain.
Exit Needle
Remove the pod holder
assembly and detach the
funnel. Locate the exit needle
on the inside bottom of the
K-Cup® pod holder. Insert a
straightened paper clip into the
exit needle to loosen any coffee
grounds.
DC0000001292 REV B
MAX
MIN
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
Entrance Needle
Lift the brewer handle and locate the entrance
needle on the underside of the lid. To clean both holes
in the needle, hold the brewer handle in the upward
position and with your other hand, carefully insert a
straightened paper clip into both holes. Gently move
it around to loosen any coffee grounds. Lower the
handle completely and run two water-only brew
cycles. Do not insert a K-Cup® pod.
CAUTION: There are sharp needles that puncture
the K-Cup® pod above the K-Cup® pod holder and
in the bottom of the K-Cup® pod holder. To avoid
risk of injury, do not put your fingers in the K-Cup®
pod holder.
Have questions? We’re here to help. Visit keurig.com/new for troubleshooting
videos, maintenance recommendations, and the full Use & Care Guide.
Still need help? Give us a call at 1-866-901-BREW (2739)
Coffeehouse taste in your own home.
FIND YOUR PERFECT POD
With over 70 brands and hundreds
of varieties, find your match at
keurig.com/new
Add Water
10
8
6
oz
SHOT
oz
oz
LATTE
MAX
To Previous Page
Loading...
Need help?
General
