Keysight Technologies PNA-L N5230A

27
For devices with 1.0 mm connectors
Mechanical calibration/verification kit
– 85059A DC to 110 GHz precision calibration/verification kit.
Includes:
85059-60003 1.00 mm (m) short 2.450 mm
85059-60007 1.00 mm (f) short 2.450 mm
85059-60004 1.00 mm (m) short 3.000 mm
85059-60008 1.00 mm (f) short 3.000 mm
85059-60002 1.00 mm (m) short 1.825 mm
85059-60006 1.00 mm (f) short 1.825 mm
85059-60001 1.00 mm (m) short 1.300 mm
85059-60005 1.00 mm (f) short 1.300 mm
85059-60009 1.00 mm male open
85059-60010 1.00 mm female open
85059-60019 1.00 mm male load
85059-60020 1.00 mm female load
85059-60021 1.00 mm lossy delay line
11920-60001 1.00 mm (m) to 1.00 mm (m) adapter
11920-60002 1.00 mm (f) to 1.00 mm (f) adapter
11920-60003 1.00 mm (m) to 1.00 mm (f) adapter
11500-60001 1.00 mm (f) to 1.00 mm (f) 8.8 cm cable
85059-60016 1.00 mm mismatch thru adapter for verification
85059-60017 1.00 mm matched thru adapter for verification
8710-2079 6 mm, 4 in-lb torque wrench
8710-2156 6 mm open end wrench
Cables
– 11500I 1.0 mm (f-f) test port cable (8.8 cm)
– 11500J 1.0 mm (m-f) test port cable (16.0 cm)
1
– 11500K 1.0 mm (m-f) test port cable (20.0 cm)
1
– 11500L 1.0 mm (m-f) test port cable (24.0 cm)
1
Adapter set
– V281C 1.0 mm(f) to V-band waveguide adapter
– V281D 1.0 mm (m) to V-band waveguide adapter
– W281C 1.0 mm (f) to W-band waveguide adapter
– W281D 1.0 mm (m) to W-band waveguide adapter
– 11920A 1.0 mm (m) to 1.0 mm (m) adapter
– 11920B 1.0 mm (f) to 1.0 mm (f) adapter
– 11920C 1.0 mm (m) to 1.0 mm (f) adapter
– 11921A 1.0 mm (m) to 1.85 mm (m) adapter
– 11921B 1.0 mm (f) to 1.85 mm (f) adapter
– 11921C 1.0 mm (m) to 1.85 mm (f) adapter
– 11921D 1.0 mm (f) to 1.85 mm (m) adapter
– 11922A 1.0 mm (m) to 2.4 mm (m) adapter
– 11922B 1.0 mm (f) to 2.4 mm (f) adapter
– 11922C 1.0 mm (m) to 2.4 mm (f) adapter
– 11922D 1.0 mm (f) to 2.4 mm (m) adapter
– 11923A 1.0 mm (f) connector launch assembly
For devices with 1.85 mm connectors
Mechanical calibration kits
– 85058B Standard: DC to 67 GHz.
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60102 1.85 mm (m) short 6.3 mm
85058-60103 1.85 mm (m) short 7.12 mm
85058-60104 1.85 mm (m) short 7.6 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60106 1.85 mm (f) short 6.3 mm
85058-60107 1.85 mm (f) short 7.12 mm
85058-60108 1.85 mm (f) short 7.6 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60111 1.85 mm male load
85058-60112 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
– 85058E Economy: DC to 67 GHz
Includes:
85058-60101 1.85 mm (m) short 5.4 mm
85058-60105 1.85 mm (f) short 5.4 mm
85058-60109 1.85 mm male open
85058-60110 1.85 mm female open
85058-60123 1.85 mm male load
85058-60124 1.85 mm female load
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
85058-60115 1.85 mm (m) to 1.85 mm (f) adapter
Electronic calibration kits
– N4694A Microwave ECal: 10 MHz to 67 GHz, 2 ports.
Includes:
Option M0F module with:
N4694-60001 1.85 mm (f) to 1.85 mm (m) ECal module
Option 00M module with:
N4694-60002 1.85 mm (m) to 1.85 mm (m) ECal module
Option 00F module with:
N4694-60003 1.85 mm (f) to 1.85 mm (f) ECal module
Option 00A adds:
85058-60113 1.85 mm (m) to 1.85 mm (m) adapter
85058-60114 1.85 mm (f) to 1.85 mm (f) adapter
Cables
– N4697E
2
Single, flexible:
1.85 mm (f) to 1.85 mm (f), 96.5 cm, 38 inches
– N4697F
2
Set, flexible:
One 1.85 mm (f) to 1.85 mm (f) cable, 62.2 cm, 24.5 inches,
p/n N4697-60100
One 1.85 mm (f) to 1.85 mm (m) cable, 62.2 cm, 24.5 inches,
p/n N4697-60200
– N4697H
2
Single, flexible:
1.85 mm (f) to 1.85 mm (m), 62.2 cm, 24.5 inches
– N4421B-B67 Set of 4, flexible:
1.85 mm (f) to 1.85 mm (m), 91.4 cm, 36 inches
Adapter set
– 85130H 1.85 mm
2
to 1.85 mm
1. For on-wafer applications, two 11500J/K/L cables are required; one cable for each test
port.
2. Special rugged female connector specically for connecting to the network analyzer
test port, but does not mate with a standard male connector.