Why is my Ki Mobility Focus CR Wheelchair pulling to one side?
If your Ki Mobility Wheelchair pulls to one side, it might be due to looseness in the chair. To resolve this, add a spacer washer between the caster stem and the bottom caster housing bearing on either the left or right side of the chair. Also, ensure the caster housings are square to the ground and remove any debris from the caster or bearings.
What to do if Ki Mobility Focus CR is difficult to turn?
If you're finding it difficult to turn your Ki Mobility Wheelchair, make sure all tire pressures are correct and equal. Also, check that all fasteners are appropriately tightened, and tighten them if necessary. Lubricate between frame connections and mating parts in suspect areas with a Teflon-based lubricant.
Why does my Ki Mobility Focus CR squeak, click or rattle?
Squeaking, clicking, or rattling in your Ki Mobility Wheelchair can often be resolved by applying a Teflon-based lubricant between frame connections and mating parts in the areas where you suspect the noise is coming from.
What causes Ki Mobility Focus CR to tilt too quickly or become difficult to recover?
If your Ki Mobility Wheelchair tilts too quickly or is difficult to recover, inspect the roller bearing for wear and replace it if necessary. Additionally, inspect the rotary frame bearing surfaces for damage and clean as needed.
How to fix caster flutter on Ki Mobility Focus CR Wheelchair?
To address caster flutter on your Ki Mobility Wheelchair, inspect the roller bearing for wear and replace it if needed. Also, check the rotary frame bearing surfaces for any damage and clean them as necessary.
Why does my Ki Mobility Wheelchair pull to one side?
Your Ki Mobility Wheelchair might pull to one side due to several reasons. It could be caused by looseness in the chair, which can be resolved by adding a spacer washer between the caster stem and the bottom caster housing bearing on the left or right side of the chair. Also, ensure all tire pressures are correct and equal. Check and tighten all fasteners appropriately if needed. Lubricate the frame connections and mating parts in suspect areas with a Teflon-based lubricant. Confirm that the caster housings are square to the ground plane and remove any debris from the caster/bearing.
Why is my Ki Mobility Mobility Aid chair difficult to tilt and recovers too quickly?
If your Ki Mobility Mobility Aid chair is difficult to tilt and recovers too quickly, try the following: add a spacer washer between the caster stem and bottom caster housing bearing on either the left or right side of the chair. Also, ensure all tire pressures are correct and equal on both sides of the chair. Make sure all fasteners are tightened. Apply a Teflon® based lubricant (such as Tri- Flow®) between modular frame components. Check that the cable/foot tilt mechanism is adjusted and cogs disengage teeth. Inspect roller bearings for wear, and replace if necessary. Inspect rotary frame bearing surfaces for damage and clean if needed. Finally, optimize the CG setting.
Why is my Ki Mobility Mobility Aid chair tilting too quickly and difficult to recover?
If your Ki Mobility Mobility Aid chair tilts too quickly and is difficult to recover, consider these solutions: add a spacer washer between the caster stem and bottom caster housing bearing on either the left or right side of the chair. Ensure all tire pressures are correct and equal on both sides of the chair. Confirm all fasteners are tightened. Use a Teflon® based lubricant (such as Tri- Flow®) between modular frame components. Verify the cable/foot tilt mechanism is adjusted and cogs disengage teeth. Inspect roller bearings for wear, replacing them if needed. Check rotary frame bearing surfaces for damage and clean them if necessary. Also, optimize the CG setting.
What to do if my Ki Mobility Mobility Aid chair does not track straight?
If your Ki Mobility Mobility Aid chair does not track straight, ensure all tire pressures are correct and equal on both sides. Also, make sure all fasteners are tightened. Inspect the rotary frame bearing surfaces for any damage and clean them as necessary.
Why is my Ki Mobility Mobility Aid difficult in tilting?
If you're experiencing difficulty tilting your Ki Mobility Mobility Aid chair, try these steps: add a spacer washer between the caster stem and bottom caster housing bearing on either the left or right side of the chair. Ensure that all tire pressures are correct and equal on both sides. Verify that all fasteners are tightened. Apply a Teflon® based lubricant (such as Tri- Flow®) between modular frame components. Check that the cable/foot tilt mechanism is adjusted and cogs disengage teeth properly. Inspect the roller bearings for wear and replace if necessary. Also, inspect the rotary frame bearing surfaces for damage, cleaning when needed. Finally, optimize the CG setting.
General| Product Category | Wheelchair |
|---|---|
| Brand | Ki Mobility |
| Model | Focus CR |
| Frame Type | Folding |
| Material | Aluminum |
| Weight Capacity | 250 lbs |
| Frame Material | Aluminum |
| Folding | Yes |
| Adjustable Backrest | Yes |
| Adjustable Footrest | Yes |
| Seat Depth | 14" - 20" |
| Weight | 28 lbs |
| Wheel Size | 24" |
To Next Page
