Kichler Lighting 0805278 User Manual

Español p. 13
ITEM #0805278
LANDSCAPE LOW VOLTAGE
TRANSFORMER
ATTACH YOUR RECEIPT HERE
Serial Number
Purchase Date
Questions, problems, missing parts? Before returning to your retailer, call our customer
service department at 1-800-554-6504, 8 a.m. - 4:30 p.m, EST, Monday - Friday.
This instruction sheet covers the installation of the following Kichler® Transformers: 12217
200 WATT DIGITAL TRANSFORMER Input: 120VAC 60Hz 2A max. Output: 12VAC/15VAC 200VA max.
Read these instructions carefully before installing this unit. Save all safety warnings and instructions for
future reference.
• This device is only accepted for use as a component of a landscape lighting system where the suitability of
the combination shall be determined by National Electric Code or local authorities having jurisdiction.
• WARNING: Risk of electric shock, use only with low voltage landscape xtures and accessories. DO not use
with swimming pool or spa lighting xtures. Do not submerge transformer.
• Caution: Use only with maximum 180 watt, 180VA lamp load and a minimum 60 watt lamp load as speci-
ed below in Finding Transformer Load.
• Do not connect two or more power supplies in parallel.
• Do not touch the product. It may get hot during normal use.
• Suitable for indoor or outdoor use.
• WARNING: Risk of Fire. If installation involves running wiring through a building structure, special wiring
methods are needed. Consult a qualied electrician.
• Transformer should be mounted close to power source. Extension cords should not be used with this unit.
• WARNING: RISK OF ELECTRIC SHOCK. Install power unit 5 feet (1.525m) or more from any pool, spa, or
fountain.
(a) indoor within 10 feet (3.05m) of a pool, spa or fountain, or
(b) outdoor, connect power to unit to a receptacle protected by a GFCI.
• WARNING: Risk of Electric Shock. When used outdoors, install only to a 115/120 volt hood covered Class-A
GFCI protected receptacle, marked “Wet Location”, that is weatherproof with the power unit connected to
the receptacle. If one is not provided, contact a qualied electrician for proper installation. Ensure that the
power unit and cord do not interfere with completely closing the receptacle cover.
• Mount the rain-tight transformer at least one 1ft (.305m) above ground level with the wire terminals facing
down. NOTE: Do not energize transformer until installation of system is complete.
• Direct burial rated wire is to be buried a maximum of 6” (152.4mm) beneath the surface of the ground.
• Risk of re. Do not place insulation under terminal plate. Check connection after installation.
1
Kichler® is a registered trademark of
The L.D. Kichler Co. All Rights Reserved.
MODEL #12217

Kichler Lighting 0805278 Specifications

General

Brand	Kichler Lighting
Model	0805278
Category	Transformer
Language	English

Summary

INSTALLATION INSTRUCTIONS

Finding Transformer Load

Calculate the required transformer wattage by summing bulb wattages and applying multipliers.

Mounting Location and Height

Guidance on selecting a mounting location and the minimum height above ground.

Cable Run Layout Options

Explains different methods for running landscape lighting cables (Series, Split, Tee).

Determining Wire Gauge and Voltage Tap

How to select cable gauge and voltage taps to minimize voltage drop for optimal light output.

Wire Connections and Torque Specifications

Instructions for connecting low-voltage wires to the terminal block and required torque.

Landscape Lighting Warranty and Limitations

Details Kichler's warranty terms for landscape lighting products and exclusions.

OPERATION

General Programming Notes

Important notes for programming the transformer functions, display, and lockout.

Setting the Clock to Local Time

Step-by-step guide to set the current time, AM/PM, hour, and minute.

Transformer Control Options Overview

Introduces three programming modes: Timer, Photo Eye Auto, and Photo Eye/Time.

Setting the Transformer Control to TIMER ON/OFF

Program the transformer to turn landscape lights on and off at specific times.

Installing the PHOTO EYE Cable

Instructions for installing the photo eye cable and advice on mounting the sensor.

Setting Transformer Control to PHOTO EYE AUTO ON/OFF

Program the transformer to turn lights on at dusk and off at dawn automatically.

Setting Transformer Control to PHOTO EYE ON / TIMER OFF

Program lights to turn on via photo eye and turn off at a user-set time.

Manual ON/OFF Override

How to manually turn landscape lights on or off, bypassing programmed settings.

Photo Eye TEST Function

Test the photo eye functionality after installation and programming is complete.

Restoring Factory Settings

Procedure to clear all programming and restore the transformer to its original factory settings.