KitchenAid KEBS107SSS04 - User Manual

Fahrenheit (°F) to Celsius (°C) Conversion
The temperature is preset in Fahrenheit; however, it can be changed to
Celsius.
To Change: Press OPTIONS and then “1” to toggle temperature between
Fahrenheit and Celsius settings.
When in Fahrenheit, “°F” follows the oven temperature.
When in Celsius, “°C” follows the oven temperature.
Adjust Oven Temperature Calibration:
1. Press OPTIONS and then “6” to set the calibration.
2. On double ovens only, press UPPER OVEN or LOWER OVEN to select
oven.
Each oven calibration can be independently set.
3. Press “3” to increase and “6” to decrease the temperature.
4. Press START to end calibration.
Diagnostics
■ Is the oven in “Sabbath Mode”? If so, “SAB” will appear in the digital
display. Press OPTIONS and “7” to end Sabbath mode. This will
return the oven to BAKE mode for an untimed bake.
Unplug oven or disconnect power before performing the following checks:
■ A potential cause of a control not functioning is corrosion on
connections. Observe connections and check for continuity with an
ohmmeter.
■ All tests/checks should be made with a VOM or DVM having a
sensitivity of 20,000Ω per volt DC or greater.
■ Check all connections before replacing components, looking for
broken or loose wires, failed terminals, or wires not pressed into
connectors far enough. Damaged harness must be entirely replaced.
Do not rework a harness.
■ Resistance checks must be made with power cord unplugged from
outlet, and with wiring harness or connectors disconnected.
Programming the Cavity Size
1. Unplug oven or disconnect power.
2. Wait 10 seconds, then plug in oven or reconnect power.
3. Enter Diagnostics mode by pressing OFF, OFF, START.
4. Press key #6 to show cavity size select screen.
5. To edit, press CLOCK key.
6. Scroll through cavity sizes by pressing key #6 until required size is
displayed.
7. Once correct size is displayed, press the START key to accept
modification.
Tech Sheet Do not discard
WARNING
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electrical shock.
Software copyrighted. This product is covered by one or more of the
following patents U.S. Patent Nos.
4,852,544
4,974,804
5,008,516
5,064,998
5,138,137
5,142,125
5,175,413
5,185,047
5,321,229
5,349,162
5,378,874
5,382,552
5,422,460
5,424,512
5,438,180
5,441,036
5,491,314
5,571,433
5,571,434
5,620,623
5,694,916
5,749,388
5,756,970
5,767,488
5,808,278
5,810,576
5,813,320
5,841,112
5,856,654
5,881,710
5,910,265
5,918,589
5,924,857
5,928,543
5,961,311
5,967,634
5,983,888
6,008,478
6,017,211
6,035,848
6,043,461
6,079,756
6,087,944
6,097,000
6,111,231
6,163,017
6,201,222
6,232,584
6,263,782
6,349,717
6,363,971
6,375,150
6,392,204
6,394,081
6,403,929
6,437,294
6,509,551
6,545,251
6,570,136
6,614,006
6,663,009
6,666,676
6,693,262
6,698,417
6,698,923
6,700,101
6,722,356
6,734,403
6,784,404
6,841,761
6,870,138
6,904,969
6,930,287
6,935,330
Other Patents Pending.
IMPORTANT: Electrostatic Discharge (ESD) Sensitive Electronics
ESD problems are present everywhere. ESD may damage or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished, but failure may occur at a later date due to ESD stress.
■ Use an antistatic wrist strap. Connect wrist strap to green ground connection point or unpainted metal in the appliance
-OR-
Touch your finger repeatedly to a green ground connection point or unpainted metal in the appliance.
■ Before removing the part from its package, touch the antistatic bag to a green ground connection point or unpainted metal
in the appliance.
■ Avoid touching electronic parts or terminal contacts; handle electronic control assembly by edges only.
■ When repackaging failed electronic control assembly in antistatic bag, observe above instructions.
W10220952A FOR SERVICE TECHNICIAN’S USE ONL
Y

Summary

Oven Safety Precautions

Electrical Shock Hazard

Critical warning about disconnecting power and replacing parts to prevent death or shock.

Electrostatic Discharge (ESD) Handling

Essential precautions for handling sensitive electronics to prevent damage from static electricity.

Oven Operational Settings

Temperature Conversion and Calibration

Instructions for converting temperature units and calibrating oven temperature settings.

Programming Cavity Size

Guide for setting the oven cavity size via diagnostic mode for proper operation.

Oven Diagnostics Overview

Diagnostics Overview

Information regarding the oven's diagnostic mode and general troubleshooting.

Oven Diagnostics Procedures

Entering Diagnostics Mode

Step-by-step instructions to access the oven's diagnostic mode for troubleshooting.

Failure;Error Display Codes

Comprehensive list of oven error codes and their likely failure conditions.

Troubleshooting Key Strokes

Guide to using specific key presses for testing oven functions and components.

Component Identification

Component Locations Diagram

Labeled diagram showing the physical location of various oven components.

Electrical Components Key

List identifying electrical components and their serviceability (Front/Rear/Top).

Oven Shutdown Thermal Cutoff

Details on the non-resettable thermal cutoff, its function, and replacement procedure.

Relay Logic

Oven Modes and Relay Operations

Table detailing relay activation for different oven modes (Bake, Broil, Clean, etc.).

Component Testing

Component Tests at Control Panel

Table outlining specific test points and expected resistance values for oven components.

Wiring Diagrams

Wiring Diagram Overview

Schematic showing electrical connections, legend, and strip circuits for oven functions.

Strip Circuits

Detailed circuit diagrams for specific oven operations like Bake Preheat.

KitchenAid KEBS107SSS04 Specifications

General

Brand	KitchenAid
Model	KEBS107SSS04
Category	Oven
Language	English