Klever Kleena K-Bot RX2

Questions and Answers

C
Christopher MurilloAug 1, 2025
Why Klever Kleena Swimming Pool Vacuum doesn't move?
- A
  Angela StanleyAug 1, 2025
  If your Klever Kleena Swimming Pool Vacuum isn't moving, first, ensure the power supply is plugged in and turned ON, and that the cable is securely connected to the power supply. Next, check that the power outlet is working and hasn't tripped a breaker. Try turning the power supply off, waiting 30 seconds, and then turning it back on. Finally, unplug the power supply, open the impeller cover, and check for any obstructions in the impeller.
N
newmanwendyAug 6, 2025
What to do if Klever Kleena Swimming Pool Vacuum cleans only part of the pool?
- A
  Anne NealAug 6, 2025
  If your Klever Kleena Swimming Pool Vacuum only cleans part of the pool, ensure there's enough slack in the cable for it to reach all areas. Also, clean the filter bag. If you have a K-Bot RX2, push in the float on the cable side (see figure A). Finally, inspect the brushes for obstructions or wear.
P
Patricia SellersAug 11, 2025
Why Klever Kleena K-Bot RX2 Swimming Pool Vacuum doesn’t climb the walls?
- M
  matthewspaulaAug 11, 2025
  If your Klever Kleena Swimming Pool Vacuum isn’t climbing walls, start by cleaning the filter bag. Then, check the chemical levels in your pool water, as improper levels can cause algae growth, making the walls slippery; adjust the levels and scrub the walls if needed. Also, inspect the brushes to ensure they aren’t worn out. If you have a K-Bot RX3, verify that the wall climbing mode hasn’t been disabled via the remote control.
W
William OwensAug 16, 2025
What to do if Klever Kleena K-Bot RX2 Swimming Pool Vacuum moves but does not clean the pool?
- T
  Tracey LongAug 16, 2025
  If your Klever Kleena Swimming Pool Vacuum moves but doesn't clean, begin by cleaning the filter bag. After starting the cleaner, observe it for a few minutes to ensure it continues moving. If it stops, inspect the impeller and drive system for any stuck debris.
W
William GregoryAug 21, 2025
How to fix cable kinks in Klever Kleena K-Bot RX2 Swimming Pool Vacuum?
- H
  Hannah PetersonAug 21, 2025
  To address cable kinks in your Klever Kleena Swimming Pool Vacuum, if you have a K-Bot RX2, push in the float on the non-cable side (see figure B). To remove the kinks, stretch the cable out completely and let it sit in the sun for at least a day.
E
eric94Aug 27, 2025
What to do if Klever Kleena K-Bot RX2 floats instead of sitting on the floor?
- I
  Ian DownsAug 27, 2025
  If your Klever Kleena Swimming Pool Vacuum floats instead of sitting on the pool floor, try removing the air again. Also, with the cleaner in the water, squeeze the combined brush/Wonder brush to ensure they are completely water absorbent.

Summary

Introduction

Specifications

Warnings and Cautions

Warnings

Safety precautions for using the power supply and the cleaner.

Cautions

Water condition requirements for optimal cleaner performance and longevity.

Pool Cleaner Parts

Brushes

Different types of brushes for various pool surfaces.

Power Supply Unit

The electrical unit that powers the pool cleaner.

Filtration

Components related to filtering debris from the pool.

Caddy Kit (if supplied)

Optional accessory for storing and transporting the cleaner.

Using the Pool Cleaner

Setup Procedure

Initial steps to prepare the pool cleaner for first-time use.

Placing Cleaner in Pool

Instructions on how to safely place the cleaner into the pool water.

Removing Cleaner from Pool

Procedure for safely retrieving the cleaner from the pool.

Cleaning the Filter Bag

Filter Bag Removal and Cleaning

Step-by-step guide to detach and clean the filter bag.

Filter Bag Replacement

Instructions for properly fitting a clean or new filter bag onto the frame.

Impeller Cleaning

How to access and clean debris from the pool cleaner's impeller.

Off Season Storage

Troubleshooting