KMB NOVAR-1214 - User Manual

KMB systems, s.r.o.
Dr. M. Horákové 559, 460 06 Liberec 7, Czech Republic
tel. +420 485 130 314, fax +420 482 736 896
email : kmb@kmb.cz, internet : www.kmbsystems.eu
6/2014
Power Factor Controllers
NOVAR-1106 / 1114 / 1206 / 1214 / 1414
NOVAR-1xxx / S400
NOVAR-1005 / 1007 / 1005D / 1007D
NOVAR-1312, NOVAR-1312-3
Firmware v. 1.7 / 1.2 ( N1312 )
Operating Manual

Summary

2. INSTALLATION

2.2 Connection

Details how to connect the controller's power supply, current, and voltage inputs.

2.2.1 Power Supply

Specifies power supply voltage ranges and connection terminals for different controller versions.

2.2.1.1 Standard Version Controllers

2.2.1.2;S400 Version Controllers

2.2.2 Measurement Voltage

2.2.3 Measurement Current

2.2.5 Output Relays

2.2.7 Communication Interface

2.2.7.1 RS-485 Communication Interface

2.2.7.2 Ethernet (IEEE802.3) Interface

3. PUTTING IN OPERATION

3.2 Automatic Connection Configuration Detection Process

Details the automated process for detecting voltage and current connection configurations.

3.3 Automatic Section Power Recognition Process

Explains the automated process for identifying compensation section power values.

4. OPERATION

4.1 Setup

Guides through configuring controller parameters for optimal compensation.

4.1.1 Editing Parameters and Clearing Recorded Measurement Values

Describes how to edit controller parameters and clear recorded measurement data.

4.1.2 Parameter 01;07 - Target Power Factor

Sets the desired target power factor or phase shift angle for compensation.

4.1.3 Parameter 02;08 - Undercompensation Control Time

Defines control intervention time for undercompensated conditions.

4.1.5 Parameter 04;10 - Control Bandwidth on High Loads

Specifies the reactive power range for compensated status at high loads.

4.1.10 Parameters 15, 16 - Type of Measurement Voltage and Connection Configuration

Configures voltage measurement type and connection methods.

4.1.13 Parameter 20 - Automatic Section Power Recognition Process

Enables or disables the automatic detection of compensation section power.

4.1.16 Parameter 25 - Compensation Section Nominal Power

Allows editing nominal power for each compensation output section.

4.1.17 Parameter 26 - Fixed Sections, Switching Cooling and Heating, Alarm

Sets sections as fixed, configures heating/cooling, and alarm functions.

4.1.19 Parameter 30 - Alarm Setting

Configures alarm indications and actuations for various nonstandard conditions.

4.1.30 Parameter 63 - Offset Control

Enables and configures offset control for reactive power adjustment.

4.2 Section Value Accurization

Explains how section values are refined after automatic recognition.

4.3 Faulty Section Indication and Disablement

Details how faulty sections are identified, indicated, and disabled.

4.4 Compensation by Choke

Describes connecting and using chokes for power system decompensation.

4.4.1 Basic Choke Compensation

Explains the asymmetric mode for choke compensation.

4.6 Manual Mode

Guides on switching to manual mode for measurements and output control.

4.8 Controller Initialization

Describes the process of resetting the controller to default settings.

4.9 Capacitor Harmonic Load factor (CHL)

8. TECHNICAL SPECIFICATIONS

Adjustable Parameters

Lists adjustable parameters across different Novar models.

Inputs and Outputs

Details electrical inputs, outputs, and their specifications.

Communication

Operating Conditions

KMB NOVAR-1214 Specifications

General

Brand	KMB
Model	NOVAR-1214
Category	Controller
Language	English