Kohler K-77795 Series

Questions and Answers

A
Adrienne EvansAug 20, 2025
How to fix a Kohler toilet that does not work?
- R
  Robert MoranAug 20, 2025
  If your Kohler toilet does not work, it might be due to a power failure. In this case, wait until the power is restored. Alternatively, check if the plug is disconnected or the socket has no power; if so, plug it in or detect the socket. Another possibility is that the leakage circuit breaker on the plug needs resetting—press the Reset button on the plug. The product might also be in standby mode, so press the button on the auxiliary keyboard. Finally, ensure the toilet switch on the side panel is turned on.
A
Antonio WolfeAug 22, 2025
What to do if my Kohler toilet fails to flush?
- C
  christytranAug 22, 2025
  If your Kohler toilet fails to flush, it could be due to a water failure, so wait until the water supply is restored. Another reason could be that the tee valve for the water supply is closed; in this case, open the tee valve. A power failure could also be the cause; wait until the power is restored or review the "manual flush" section for manual flushing. If the product is in standby mode, press the button on the auxiliary keyboard. Also, if the wash mode is in progress, perform the after-flushing operation once it is completed.
D
danielclarkAug 23, 2025
Why is my Kohler toilet remote unable to display?
- A
  Andrew NicholsAug 25, 2025
  If the remote is unable to display for your Kohler toilet, the batteries may be exhausted; replace them with new ones. Another reason could be that the battery polarities are mounted reversely; reinstall them properly. Also, the remote controller might not be woken up; touch the remote controller screen when approaching the toilet or while seated.
B
Brett BarnettAug 26, 2025
Why is the wash mode abnormal on my Kohler toilet?
- S
  Stephen GriffinAug 26, 2025
  If your Kohler toilet's wash mode is abnormal, it might be due to a water failure, so wait until the water supply is restored. Another possibility is that the tee valve for the water supply is closed or not fully opened; fully open the tee valve. If the product is in standby mode, press the button on the auxiliary keyboard. The issue could also be that you are not yet seated or your current sitting posture cannot be sensed by the seat; try to seat or adjust your sitting gesture. Insufficient water pressure can also cause this; check for any bends in the inlet hose and adjust it if necessary.
M
Megan HortonAug 27, 2025
Why is the seat not warm on my Kohler toilet?
- P
  Paul ChapmanAug 27, 2025
  If the Kohler toilet seat is not warm, it could be that the remote seat temperature is set too low; set the seat temperature to the appropriate dial. Alternatively, the toilet might be in standby mode; press the " " button on the auxiliary keyboard.
P
Paul BennettAug 29, 2025
Why does the flush function stop when using my Kohler toilet?
- K
  Karen HarrisAug 30, 2025
  If the flush function on your Kohler toilet stops during operation, it may be because the flushing mode automatically stops after continuous flushing for 5 minutes; if necessary, press the Flush button again. It could also be that the seat is unable to sense the human body; adjust your sitting posture or sit on the toilet again.
A
Amanda Ramos PhDAug 31, 2025
Why does my Kohler toilet remote control fail to connect?
- J
  James ZimmermanSep 1, 2025
  If the remote control fails to connect to your Kohler toilet, it could be due to low battery; review the "Usage and replacement of battery for remote control" chapter and replace the battery accordingly. Another reason might be that the remote control is too far from the toilet; review the section on "Communication between remote controller and the toilet" and approach the toilet. Also, the toilet might not be powered on yet; power on the toilet. If the toilet is on standby mode, press the " " button on the auxiliary keyboard. Finally, the toilet might not be connected to the remote control; review the section on "Communication between remote and toilet" and connect the toilet and the remote accordingly.
H
hornkathleenSep 2, 2025
What to do if my Kohler toilet is not clean after flushing?
- A
  Amanda GloverSep 2, 2025
  If your Kohler toilet is not clean after flushing, the filter screen might be blocked (refer to the "Filter screen clean" section). Another potential cause is insufficient water pressure; check if all tee valves are opened. Also, check for any bending issues on the inlet hose and adjust the hose if necessary.
A
Ann ValdezSep 5, 2025
Why does the dryer fan stop when using my Kohler toilet?
- P
  Patricia JonesSep 5, 2025
  If the dryer fan on your Kohler toilet stops during operation, it could be because the dryer fan stops automatically after continuous usage for 4 minutes; if necessary, press the dryer button again. Another reason could be that the seat is unable to sense the human body; adjust your sitting gesture or sit on the toilet again.
R
rgeorgeSep 6, 2025
Why does the wash mode run when unseated on my Kohler toilet?
- M
  Melissa NicholsonSep 6, 2025
  If the wash mode runs even when you are unseated from your Kohler toilet, the seat may be covered by foreign matters or the seat is wet; remove any foreign matters or dry the seat.