Kohler RIALTO K-3386-JA User Manual

HOW TO USE THESE INSTRUCTIONS
Please read these instructions carefully to familiarize yourself
with the required tools, materials, and installation sequences.
Follow the sections that pertain to your particular installation.
This will help you avoid costly mistakes. In addition to proper
installation, read all operating and safety instructions.
All information in these instructions is based upon the latest
product information available at the time of publication. Kohler
China reserves the right to make changes in product
characteristics, packaging, or availability at any time without
notice.
These instructions contain important care, cleaning, and
warranty information -
.
please leave instructions for the
consumer
-
ORDERING INFORMATION
NOTES
Rialto Gravity Toilet K-3386-JA
Includes seat K-4662T-**/K-
Observe all local plumbing and building codes.
Shut off the water supply.
Seat post holes are on 140mm (5-1/2") centers.
51mm (2") passageway.
Water depth from the rim is 155mm (6-1/1/2").
Ensure that the new drain has the correct roughing-in
dimension. This toilet has a 305mm (12") roughing-in
dimension. .
Closet flange must be 305mm (12") on-center from wall.
Carefully inspect the new fixture for any sign of damage.
For new construction, refer to the dimensions in
for locating the shut-off valve.
Fixture dimensions are nominal and conform to tolerances
established by ASME Standards (A112.19.2M).
: Handle vitreous china products very carefully.
Vitreous china can break and chip if you overtighten
bolts and nuts.
. The fill valve
nut has been factory-tightened to design specifications.
If re-tightening is required, wrench tighten one turn
past finger tight .
TM
4663-**
·
·
·
·
·
·
·
·
·
·
See Fig. #1
Fig. #1
and Fig. #4
WARNING: Risk of personal injury or product
damage
WARNING: Risk of external leakage
K-3386-JA
K-4662T-**/K-4663-**
140mm
51mm
155mm
305mm(
1)
305mm
14
ASME A112.19.2M.
·
·
·
·
·
·
·
·
·
·
1033004-T01-A
INSTALLATION INSTRUCTIONS
VITREOUS CHINA SIPHON WASH ONE-PIECE TOILET
S-PB K-3386-JA
RIALTO
ã
ã
, 2003
Copyright Kohler China Ltd., 2003
528137

Kohler RIALTO K-3386-JA Specifications

General

Brand	Kohler
Model	RIALTO K-3386-JA
Category	Other
Language	English

Summary

BEFORE YOU BEGIN

HOW TO USE THESE INSTRUCTIONS

Guide on how to read and follow installation instructions for safety and error avoidance.

ORDERING INFORMATION

Details about product ordering, including model numbers and included parts.

INSTALLATION NOTES

Important installation notes, local codes, water depth, and fixture dimensions.

SAFETY WARNINGS

Critical warnings regarding personal injury, product damage, and external leakage during installation.

TOOLS AND MATERIALS REQUIRED

ROUGHING-IN AND INSTALLATION

TO REMOVE EXISTING TOILET

Step-by-step instructions for safely removing an old toilet from the installation site.

INSTALLATION PROCEDURES

TO INSTALL SUPPLY SHUT-OFF VALVE

Instructions for installing the water supply shut-off valve at the correct height and position.

TO INSTALL BOWL

Steps for placing the toilet bowl and ensuring a proper seal with the gasket and closet flange.

CAUTION: CONCEALED LEAKAGE RISK

Warning about potential hidden leaks and the need to replace the gasket if the seal is broken.

WATER SUPPLY CONNECTION

CONNECTING THE WATER SUPPLY

Guidance on connecting the water supply line to the fill valve, recommending flexible hoses.

PRE-USE SYSTEM FLUSH

Critical steps to flush debris from the water system before fully turning on the supply.

FLOAT ADJUSTMENT AND TROUBLESHOOTING

FILL FLOAT WITH BALLAST

Instructions on adjusting the float mechanism to achieve the correct water level in the tank.

TROUBLESHOOTING CHART

A table listing common toilet symptoms, their probable causes, and corrective actions.

IMPORTANT CONSUMER INFORMATION

CONSUMER RESPONSIBILITIES

Outlines user duties for maintaining toilet function, cleaning, and avoiding damage.

WARNING: PROPERTY OR PRODUCT DAMAGE

Crucial warning against using in-tank cleaners containing chlorine due to potential damage.

LIMITED ONE-YEAR WARRANTY

Details the one-year limited warranty for plumbing fixtures and fittings, covering manufacturing defects.

SERVICE PARTS