Kolver EDU1FR/SG

Manual EDU 2AE/TOP e EDU 2AE/TOP/TA Rev.1.1 Page 7
16) Reset aut : If ON, the control unit resets automatically after a cycle end.
If OFF, press OK every cycle end.
17) Press ESC: If ON, the control unit will after an error signal, then press ESC to reset.
If OFF, the control unit resets automatically.
-
-
-
-
-
M
E
N
U
-
-
P
R
:
1
-
-
-
-
-
1
8
)
E
r
r
o
r
l
e
v
e
r
:
O
N

1
9
)
D
e
f
i
x
a
l
l
o
w
:
O
F
F
2
0
)
C
a
l
i
b
r
a
t
i
o
n
:
O
N
18) Error lever: If ON, an error signal will occur if the lever has released before reaching the torque.
If OFF, this function doesn’t work.
19) Defix allow: if ON, the reverse switch on the PLUTO will work normally. If OFF, if you want the
screwdriver will work only forward.
20) Calibration: If ON, you will see the torque value (Nm or in.lbs) on the main screen.
If OFF, the torque value won’t be displayed.
(To modify the calibration parameters see paragraph Torque calibration).
-
-
-
-
-
M
E
N
U
-
-
P
R
:
1
-
-
-
-
-
2
1
)
C
o
m
p
e
n
s
:
+
0
.
0
0
N
m

2
2
)
U
n
i
t
:
N
m
2
3
)
T
o
r
q
m
i
n
:
0
.
0
0
N
m
21) Compens – Compensation: This function allows an increase or decrease of the displayed torque
after calibration. The available range is from 0 to ±9.99 Nm. For example: after calibration (see Torque
calibration) you make a screwing cycle on your assembly and compare the value you see on the main screen
display with the value you see on a torque tester (for example a mini-K or a K model). Let's say you notice
that the torque displayed in the unit EDU 2AE/TOP is +0.2 Nm higher than the value indicated on the tester
(which is the right one). In this case you change this value by setting -0.2 Nm so that the value on the screen
will be the same as the value on the tester. If it’s lower than 0.3 Nm, you need to set +0.3 Nm and so on.
22) Unit: You can choose between the following units of measurements: Nm and in.lbs.
23) Torq min – Minimum torque: The minimum torque and maximum torque options allow the user to
set the acceptable torque range for each single application. When the reached torque is inside this range,
“tightening OK” will be displayed on the status bar and the green led will light up. If the reached torque is
outside this range the messages “error minimum torque” or “error maximum torque” will be displayed. You
can set the torque range from 0 to 40 Nm in steps of 0.01 Nm.
The minimum torque option allows to set the lowest value of the torque range and it’s on if calibration is
ON. If calibration is OFF, the minimum torque value automatically sets on 0 Nm.
-
-
-
-
-
M
E
N
U
-
-
P
R
:
1
-
-
-
-
-
2
4
)
T
o
r
q
m
a
x
:
4
0
.
0
0
N
m

2
5
)
I
n
s
.
b
a
r
c
o
d
e
2
6
)
F
u
n
c
T
&
A
:
O
F
F