EG-25
SERVICE DATA
Tightening Torque (Cont'd)
MAIN TIGHTENING TORQUE
* : Parts with tightening sequence
1) - :Tighten separately in several turns.
Unit :N•m (kg-m, ft-lb)
N•m (kg-m, in-lb)*
Parts name or location Tightening torque
Adjusting screw Lock nut 16 - 22 (1.6 - 2.2, 12 - 16)
AlternatorAdjusting bar side
Bracket side
17.5 - 23.7 (1.8 - 2.4, 13 - 17)
50.0 - 67.6 (5.1 - 6.9, 37 - 50)
Oil pan drain plug 54 - 59 (5.5 - 6.0, 40 - 43)
Spark plug 20 - 29 (2.04 - 2.96, 14 - 22)
* Intake manifold 15.7 - 18.6 (1.6 - 1.9, 12 - 14)
* Air horn 20.6 - 26.5 (2.1 - 2.7, 16 - 27)
Exhaust manifold cover 6.37 - 7.45 (0.65 - 0.76, 56 - 66)*
* Exhaust manifold 27 - 31 (2.8 - 3.2, 20 - 23)
Exhaust manifold connector 59 - 78 (6.0 - 8.0, 43 - 58)
* Oil pan [M6]
[M8]
6.3 - 8.3 (0.64 - 0.85, 56 - 74)*
15.7 - 20.6 (1.6 - 2.1, 12 - 15)
Oil strainer 16 - 19 (1.6 - 1.9, 12 - 14)
* Rocker cover 1.0 - 2.9 (0.1 - 0.3, 9 - 26)*
Rocker shaft bracket 15.6 - 21.6 (1.6 - 2.2, 12 - 16)
* Cylinder head bolt 1) 29.4 (3, 22)
2) 61.7 (6.3, 46)
3) 0 (0, 0)
4) 29.4 (3, 22)
5) 69q - 74q(Angle tightening)
Cylinder head additional bolt 6.4 - 7.5 (0.65 - 0.76, 56 - 66)*
Crankshaft pulley 181 - 191 (18.5 - 19.5, 134 - 141)
* Front cover 15.7 - 20.6 (1.6 - 2.1, 12 - 15)
Camshaft sprocket 132.3 - 142.1 (13.5 - 14.5, 98 - 105)
Chain tensioner 5.6 - 8.4 (0.57 - 0.86, 49.5 - 74.7)
Distributor 9.35 - 11 (0.95 - 1.1, 82 - 95)*
Camshaft locating plate 5.6 - 8.4 (0.57 - 0.86, 49.5 - 74.7)
* Flywheel 146 - 167 (15 - 17, 108 - 123)
* Main bearing cap 162 - 172 (16.5 - 17.5, 119 - 127)
Connecting rod nut 1) 38 - 40 (3.9 - 4.1, 28 - 30)
2) 40q - 45q(Angle tightening)
Engine coolant drain plug 34 - 44 (3.5 - 4.5, 25 - 33)
Water pump 15.7 - 18.6 (1.6 - 1.9, 12 - 14)
Engine coolant temperature sensor 20 - 29 (2.0 - 3.0, 14 - 22)
PCV valve 20 - 29 (2.0 - 3.0, 14 - 22)
* Fuel tube 1) 9.3 - 20.6 (0.9 - 2.1, 78 - 182)*
2) 20.6 - 26.5 (2.1 - 2.7, 15 - 20)
Starter motor 41.2 - 52 (4.2 - 5.3, 30 - 38)
Heated oxygen sensor 1 40 - 60 (4.1 - 6.1, 30 - 44)
To Previous Page
Loading...
