Konica Minolta 7115 User Manual (English)

Other manuals for Konica Minolta 7115

User Guide163 pages

Operating Instructions148 pages

Questions and Answers:

G
Glenn PonceAug 22, 2025
Why does my Konica Minolta 7115 Copier produce copies with lines?
- S
  Sean LoweAug 22, 2025
  If your Konica Minolta Copier produces copies with lines, it could be due to several reasons: the Original Glass surface is dirty (wipe it clean with a soft dry cloth), the Original Pad is dirty (wipe it clean with a soft cloth dampened with neutral detergent), the original is highly transparent (place a blank sheet of paper over the original), or the original is 2-sided (adjust the image density to the lighter side).
M
Matthew ColemanAug 23, 2025
What to do if the Konica Minolta 7115 cannot be turned ON?
- J
  Jessica SnyderAug 25, 2025
  If your Konica Minolta Copier won't turn on, make sure the power cord is plugged into the power outlet. Also, check if the room’s circuit breaker is tripped and close it if necessary.
J
Jonathan LoweryAug 25, 2025
Why is the image on my Konica Minolta 7115 Copier too dark?
- J
  Julie BestAug 26, 2025
  If the image is too dark on your Konica Minolta Copier, the image density is likely set to "Darker". Adjust the image density to the lighter side.
C
Corey GonzalezAug 27, 2025
Why is the image on my Konica Minolta 7115 Copier too light?
- S
  samanthapattersonAug 27, 2025
  If the image is too light on your Konica Minolta Copier, the image density is likely set at "Lighter". To fix this, adjust the image density to the darker side.
T
tonyaclayAug 27, 2025
What to do if the copy from Konica Minolta Copier is blurry?
- C
  Chad MartinAug 27, 2025
  If the copy from your Konica Minolta Copier is blurry, it could be because the paper is damp (change the paper) or the original is not placed firmly against the Original Glass (place the original in position so that it is placed firmly against the Original Glass).
K
Kenneth PetersonAug 29, 2025
Why is the edge of the copy dirty on my Konica Minolta 7115 Copier?
- M
  Mark DonaldsonAug 29, 2025
  If the edge of the copy is dirty on your Konica Minolta Copier, it could be due to several reasons: the Original Pad is dirty (wipe it clean with a soft cloth dampened with neutral detergent), you have selected paper of a size larger than the original when the zoom ratio is full size (select the same paper size as the original), the original is not placed in the correct position when the zoom ratio is full size (select the same paper size as the original), or the reduction ratio selected is not in accord with the paper size when the copy is made at a manually adjusted reduction ratio (select the zoom ratio according to the paper size).
C
Cynthia WilliamsonAug 30, 2025
Why does my Konica Minolta 7115 have lines on the copy?
- T
  Tyler SchaeferAug 30, 2025
  Lines on your Konica Minolta Copier copies may appear due to several reasons: * The Original Glass surface might be dirty. If so, wipe the Original Glass clean with a soft dry cloth. * The Original Pad might be dirty. In this case, wipe the Original Pad clean with a soft cloth dampened with neutral detergent. * The original may be highly transparent, try placing a blank sheet of paper over the original. * If the original is 2-sided, the information on the backside of a thin original may be slightly reproduced on the copy. Adjust the image density to the lighter side.
J
Jeffrey GallegosAug 31, 2025
How to fix a Konica Minolta 7115 that will not turn on?
- S
  sancheztammySep 1, 2025
  If your Konica Minolta Copier will not turn on, check the following: * Ensure the power cord is plugged into the power outlet. If it's unplugged, plug it in. * Check the room’s circuit breaker. If it's tripped, close it.
A
Annette GarrettSep 2, 2025
What to do if the image is too dark on my Konica Minolta Copier?
- S
  Sara FrankSep 2, 2025
  If the image is too dark on your Konica Minolta Copier, it's likely that the image density is set to "Darker." Adjust the image density to the lighter side.
S
Sandra ShermanSep 3, 2025
How to fix light images from Konica Minolta 7115 Copier?
- V
  Vincent BeckerSep 3, 2025
  If the image is too light when using your Konica Minolta Copier, the image density is likely set at "Lighter." Adjust the image density to the darker side.