Why does my Konica Minolta Copier regularly report a paper jam?
If your Konica Minolta Copier is regularly reporting paper jams, it might be due to labels or OHP transparencies used previously. Check for any labels stuck in the reported paper jam location and use the bypass tray for special paper. Additionally, ensure that the paper is loaded correctly.
What to do if Konica Minolta Copier won't copy after a paper jam?
If copying cannot be continued on the Konica Minolta Copier after a paper jam, clear all paper jams that you can find.
Why is nothing showing on the Konica Minolta Copier display?
If nothing is displayed on the Konica Minolta Copier, it might be due to several reasons. First, the energy-saving function could be enabled; press any key to deactivate it. Second, the system might be switched off, so turn it on. Third, check that the main switch is set to the 'I (ON)' position. Finally, ensure that the power plug is properly plugged into the outlet.
Why will my Konica Minolta Copier not switch on?
If your Konica Minolta Copier won't switch on, ensure the power plug is correctly inserted into the outlet. Also, check that the main switch is in the 'I (ON)' position. Finally, verify that the building's circuit breaker hasn't been activated; if it has, switch it back on.
What to do if Konica Minolta Copier doesn't start when pressing the start key?
If a cycle doesn't start when you press the [START] key on the Konica Minolta Copier's control panel, make sure all doors on the system or finisher are closed. Also, verify that a matching paper size is loaded and that the copy counter isn't at '0'. Input your E.K.C. password if required. If the copy limit has been exceeded, contact the system administrator. Ensure the basic options are displayed, exit energy-saving mode, and note any malfunction messages shown on the display.
Why is the finisher not working on my Konica Minolta Copier?
If the Konica Minolta Copier finisher isn't working, check for and clear any paper jams. Ensure the finisher door is closed and verify that a finisher function is enabled in the output menu.
How to fix blurred copies on a Konica Minolta Copier?
If copies from your Konica Minolta Copier are blurred, try changing the basic exposure options. Clean the original glass, ensure the original is flat against the glass, and manually brighten the copy's exposure if it's too dark.
What to do if Konica Minolta Copier copies have spots?
If copies from the Konica Minolta Copier have spots, clean the original glass and cover. If the original is very thin or transparent, place a sheet of white paper on top. For originals printed on both sides or if the exposure level is too dark, manually brighten the exposure of the copy.
Why does my Konica Minolta Copier make copies with a dark edge?
If the Konica Minolta Copier is producing copies with a dark edge, clean the original cover. Make sure the original is correctly positioned on the glass. Use paper of the same size as the original, and select a suitable lens mode.
How to fix a Konica Minolta Copier when the copy is not straight?
If copies from your Konica Minolta Copier are not straight, ensure the original is correctly positioned on the original glass or in the original feed. If using the EDH, and the original is unsuitable, place it on the original glass instead.
General| Type | Digital Copier |
|---|---|
| Printing Technology | Laser |
| Print/Copy Speed | 55 ppm |
| Max Paper Size | A3 |
| Resolution | 600 x 600 dpi |
| Original Size | A3 |
| Duplex | Yes |
| Scanner | Optional |
| Printer | Optional |
| Fax | Optional |
| Connectivity | USB |
| Reduction/Enlargement | 25% to 400% |
| Paper Sizes | A3, A4, A5, B4, B5 |
| Power Consumption | 1.5 kW (max) |
| Network Ready | Yes |
To Next Page
