Konig DL-DANCER250 - User Manual

Questions and Answers

E
Edgar LevyAug 12, 2025
What to do if Konig DL-DANCER250 DJ Equipment fixtures reset correctly but some respond erratically to controller?
- P
  Philip SullivanAug 12, 2025
  If your Konig DJ Equipment fixtures reset correctly but some respond erratically or not at all to the controller, consider the following potential causes and solutions: * **Bad data link connection:** Inspect connections and cables, correct poor connections, and repair or replace damaged cables. * **Data link not terminated:** Insert a termination plug in the output of the last fixture on the link. * **Incorrect fixture addressing:** Check the DMX addresses. * **One of the fixtures is transmitting as a master:** Check all fixture settings.
B
benjamin39Aug 15, 2025
What to do if Konig DL-DANCER250 DJ Equipment fixtures reset correctly but some respond erratically or not at all to controller?
- M
  Michelle WilliamsAug 15, 2025
  If your Konig DJ Equipment fixtures reset correctly but some respond erratically, it might be due to a defective fixture. To identify the issue, bypass one fixture at a time by unplugging both DMX connectors and connecting them directly together until normal operation is regained. The defective fixture has to be serviced by a technician.
C
Christine WeeksAug 20, 2025
What to do if Konig DL-DANCER250 DJ Equipment fixtures reset correctly but all respond erratically to controller?
- O
  Olivia ThorntonAug 20, 2025
  If your Konig DJ Equipment fixtures reset correctly, but all respond erratically or not at all to the controller, it could be due to: * A disconnected controller: Connect the controller. * Mismatched XLR pin-out: Install a phase-reversing cable between the controller and the first fixture on the link if the XLR pin-out of the controller does not match the pin-out of the first fixture on the link (polarity is reversed).
V
Vanessa WagnerAug 23, 2025
What to do if my Konig DL-DANCER250 has no light output?
- E
  Edward Herman Jr.Aug 23, 2025
  If your Konig DJ Equipment fixture is working correctly but has no light output, the cause may be a broken or worn-out lamp. Install a new lamp.
J
Jessica RhodesAug 27, 2025
Why does my Konig DL-DANCER250 lamp cut out intermittently?
- P
  Paul MoraAug 27, 2025
  If the lamp in your Konig DJ Equipment cuts out intermittently or burns out too quickly, it may be because the fixture is too hot. Allow the fixture to cool, ensure free airflow around it, and check and clean the fan and grills if necessary.
R
Richard TaylorAug 30, 2025
How to fix Konig DJ Equipment not responding to music beat?
- E
  Erika RichardsonAug 30, 2025
  If your Konig DJ Equipment does not respond correctly to the music beat in music trig mode, the music level sensitivity might be incorrectly adjusted. Use the control panel to adjust the sensitivity until the fixture responds satisfactorily.
R
Rebekah JordanSep 3, 2025
What to do if my Konig DL-DANCER250 is completely dead?
- J
  James RodriguezSep 3, 2025
  If one or more of your Konig DJ Equipment fixtures are completely dead, check the following: * **Power:** Make sure that the cables are plugged in and the power is switched on. * **Main fuse:** If the above is correct, the main fuse may be blown. Replace the fuse.
M
Michael Kim DDSSep 7, 2025
Why does Konig DJ Equipment display a number and not run a light show?
- S
  Shannon YoungSep 8, 2025
  If a number appears in the display of your Konig DJ Equipment and it will not run a standalone light show, the fixture is likely set to DMX mode and is displaying its DMX address. Use the control panel to change the fixture from DMX to standalone auto trig or music trig.