Konig DL-QUAKE250 User Manual (English)

Questions and Answers:

A
annesimmonsAug 7, 2025
What to do if Konig DL-QUAKE250 DJ Equipment fixtures respond erratically to the controller?
- C
  Christine CarterAug 7, 2025
  If your Konig DJ Equipment fixtures reset correctly but some respond erratically or not at all to the controller, there might be a bad data link connection. Inspect the connections and cables, correct any poor connections, and repair or replace damaged cables. Also, ensure the data link is terminated with a 120 Ohm termination plug inserted in the output of the last fixture on the link. Check the DMX addresses to make sure they are correct. Verify that none of the fixtures are transmitting as a master by checking all fixture settings. As a last resort, one of the fixtures may be defective. Bypass one fixture at a time (unplug both DMX connectors and connect them directly together) until normal operation is regained. The defective fixture has to be serviced by a technician.
C
Cody McgrathAug 11, 2025
How to troubleshoot Konig DJ Equipment that is completely dead?
- A
  Angela DavisAug 11, 2025
  If one or more of your Konig DJ Equipment fixtures are completely dead, the issue could be due to no power reaching the fixture. To resolve this, ensure that all cables are properly plugged in and that the power is switched on. Additionally, check if the main fuse has blown and replace it if necessary.
M
millerstephenAug 15, 2025
Why is there no light output from my Konig DL-QUAKE250 DJ Equipment?
- M
  Melissa ColemanAug 15, 2025
  If your Konig DJ Equipment fixture is working correctly but there is no light output, it is likely due to a broken or worn-out lamp. To fix this, install a new lamp.
P
padillastephenAug 19, 2025
Why do all my Konig DL-QUAKE250 fixtures respond erratically?
- G
  George TurnerAug 20, 2025
  If your Konig DJ Equipment fixtures reset correctly but all respond erratically or not at all to the controller, first, check that the controller is properly connected. If it is, the issue might be due to an XLR pin-out mismatch between the controller and the first fixture on the link, where the polarity is reversed. To correct this, install a phase-reversing cable between the controller and the first fixture on the link.
A
April StarkAug 23, 2025
How to adjust music sensitivity on Konig DL-QUAKE250?
- J
  Jonathan ThomasAug 25, 2025
  If your Konig DJ Equipment fixture does not respond correctly to the music beat in music trig mode, the music level sensitivity might be incorrectly adjusted. Use the control panel to adjust the sensitivity until the fixture responds satisfactorily.
K
Kevin CraigAug 28, 2025
What to do if Konig DL-QUAKE250 shows a number and won't run a light show?
- C
  Craig BrownAug 28, 2025
  If a number appears on the display of your Konig DJ Equipment and the fixture will not run a standalone light show, it is likely that the fixture is set to DMX mode and is displaying its DMX address. To resolve this, use the control panel to change the fixture from DMX mode to standalone auto trig or music trig mode.
N
Nicholas VargasSep 1, 2025
Why does the lamp in my Konig DL-QUAKE250 burn out quickly?
- R
  Robert DavisSep 1, 2025
  If the lamp in your Konig DJ Equipment cuts out intermittently or burns out too quickly, the fixture might be overheating. Allow the fixture to cool down, ensure there is free airflow around it, and check and clean the fan and grills if necessary.

Konig DL-QUAKE250 Specifications

General

Brand	Konig
Model	DL-QUAKE250
Category	DJ Equipment
Language	English

Related product manuals

Konig DL-DANCER250

69 pages

Konig DL-QUAKE250 User Manual

Table of Contents

Questions and Answers:

Konig DL-QUAKE250 Specifications

Related product manuals